19-05-2016, 12:35 PM
Thanks for all the replies guys, need to get this sorted now really.
Guys thoughts:
So without sounding like a douche bag, how do I check the coil and injectors have a good power supply? I'm very noob when it comes to wiring / electricals so it's all new to me.
I've looked at these from: http://www.306gti6.com/forum/showthread....340&page=1
My coil wiring is different to this right so what am I prodding where with my multimeter to check for power supply whilst cranking?
![[Image: Injectors.jpg]](http://img.photobucket.com/albums/v259/PeterSims8/Sensors/Injectors.jpg)
![[Image: Coils.jpg]](http://img.photobucket.com/albums/v259/PeterSims8/Sensors/Coils.jpg)
Here's few pics of the bay / plugs / etc.
The bay:
![[Image: IMG_9740.jpg]](http://s32.postimg.org/8e3fxkhxd/IMG_9740.jpg)
Injectors plug 1:
![[Image: IMG_9741.jpg]](http://s32.postimg.org/87uc87y69/IMG_9741.jpg)
Coil pack plug:
![[Image: IMG_9742.jpg]](http://s32.postimg.org/kethc1ept/IMG_9742.jpg)
Wiring going to Relays & Omex:
![[Image: IMG_9744.jpg]](http://s32.postimg.org/l1se1kblt/IMG_9744.jpg)
Relays for coils, injectors, lambda, fans, have tried switching these around, no difference, are working fine.
Guys thoughts:
Quote:6v is a little low, however, the ECU is live because Run Time is counting and is receiving the correct signal from the crank sensor, Engine Speed is showing a correct value and Stat Sync’d is going ON. Providing the calibration is correct this means the ECU is operating its outputs so I would advise you to check the coil and injectors have a power supply whilst cranking the engine.
So without sounding like a douche bag, how do I check the coil and injectors have a good power supply? I'm very noob when it comes to wiring / electricals so it's all new to me.
I've looked at these from: http://www.306gti6.com/forum/showthread....340&page=1
My coil wiring is different to this right so what am I prodding where with my multimeter to check for power supply whilst cranking?
![[Image: Injectors.jpg]](http://img.photobucket.com/albums/v259/PeterSims8/Sensors/Injectors.jpg)
![[Image: Coils.jpg]](http://img.photobucket.com/albums/v259/PeterSims8/Sensors/Coils.jpg)
Here's few pics of the bay / plugs / etc.
The bay:
![[Image: IMG_9740.jpg]](http://s32.postimg.org/8e3fxkhxd/IMG_9740.jpg)
Injectors plug 1:
![[Image: IMG_9741.jpg]](http://s32.postimg.org/87uc87y69/IMG_9741.jpg)
Coil pack plug:
![[Image: IMG_9742.jpg]](http://s32.postimg.org/kethc1ept/IMG_9742.jpg)
Wiring going to Relays & Omex:
![[Image: IMG_9744.jpg]](http://s32.postimg.org/l1se1kblt/IMG_9744.jpg)
Relays for coils, injectors, lambda, fans, have tried switching these around, no difference, are working fine.
![[Image: IMG_9745.jpg]](http://s32.postimg.org/6oprbrcu9/IMG_9745.jpg)