Jons Wagon Thread. Questions will be asked (a lot)

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Jons Wagon Thread. Questions will be asked (a lot)
#91
Jon I have a mint front pair of half leathers if you're interested?
Welding and fabrication projects undertaken, contact me for more information.

Reply
Thanks given by:
#92
Cheers buddy. It was more of a question for the moment as I'm broke.
I'll bare it in mind for the future though. Unless they're cheaper than the proverbial budgie Wink
Reply
Thanks given by:
#93
Make me an offer if you want, I can always say no Big Grin
Welding and fabrication projects undertaken, contact me for more information.

Reply
Thanks given by:
#94
£7.62, half a pack of gum and some assorted pocket fluff. Lol.
Seriously though, I can't afford anything untill tge new year.
Chrismas is expensive in my house, the wife and daughter have horses & 2 new saddles aren't cheap :O
Lol
Reply
Thanks given by:
#95
Fair enough man, they're not going anywhere so give me a shout if and when you want them?
Welding and fabrication projects undertaken, contact me for more information.

Reply
Thanks given by:
#96
If you could pm me what your looking for, for them, I know how much overtime put in. Pol
Reply
Thanks given by:
#97
(05-12-2013, 03:42 AM)Lego Jon Wrote: Blatantly stole this link. Pretty much a blow by blow fitting guide for HDI Fmic.
http://www.club-306.com/topic/12625-hdi-...r-fitting/
Theres a few bits I dont like in that guide but Its not bad.
Dont cut down a bottom pipe as itll split.
Dont bother with gasket paper as the proper gasket is pennies
And try and use as few joiners as possible as theres one bit where hes got about half a dozen clamps within a foot of pipe run. If you want to join metal to metal get them welded.




(09-12-2013, 04:04 PM)Lego Jon Wrote: Finally sorted out my hockey stick.
My pug finaly doesn't look like it's had a stroke.
LMFAO.
Still missing the cap for my roof bar... doh!

So, a question....

I've got half leather seats that are well past their prime.
Can I swap them out for another set of 5 door seats?
Also I have grey cloth door cards, can they be swapped out so they match the seats?
Do they need to be phase specific and are they straight swap from a 5 door?

Depending on how bad your 5dr seats are I'd do a straight swap for my BMW ones and their mounts

Oh and any 5dr seats will fit out of any phase but early ones wont have the airbags.
Reply
Thanks given by:
#98
Yeah, I wasn't planning on having that many joins as its too much of a risk. Weak links in the chain and all that.

Well to be honest, on the seat cushion (drivers) theres a patch of leather worn away mate. The pass is fine.
Thanks for the kind offer. Smile
Reply
Thanks given by:
#99
A few bits today...
[Image: IMG-20131210-WA0002_zpsb9bf6aee.jpg]
Reply
Thanks given by:
Just in case you were wondering, the part number for the cast top piece thermostat housing is 1336p2 from pug and is £11.06 +vat.
Reply
Thanks given by:
Well, sorted the tensioner out. It was easier with the engine dropped. Lol.
Also got my new tailgate badge on.

[Image: 20131217_212501_zps011d7645.jpg]

And a few shots of the wagon and my brother in laws 205 DT ...

[Image: 20131217_212202_zps771c2fc8.jpg]

[Image: 20131217_212050_zps986f0752.jpg]

[Image: 20131217_211945_zpsb7087d23.jpg]
Reply
Thanks given by:
So, what size are the front and rear wipers on the Estate?
Cheers
Reply
Thanks given by:
the rear wiper youll have to order from peugeot. They didnt stock it last time i went. The halfords ones and ebay ones dont fit properly. I was driving along at 50 and used the rear wiper and it came off (probably hit the car behind) and scratched my window!
Reply
Thanks given by:
Ok. I'll bear that in mind.
What about the fronts? My drivers smears like fook and is annoying me.

Also about that cap mate. How much you want etc?
Ta
Reply
Thanks given by:
Fronts are 20" and 22" iirc, but a tape measure/ruler/bit of string looped round an lp a few times will tell you if you'd rather be sure. Wink
306 HDi Deathtrap - 130bhp / 220lbft
...UPGRADING...



Reply
Thanks given by:
Mine are cheap equal 19" ones, tis why I asked
Wink
Reply
Thanks given by:
Ah i see, sorry haha! These are the ones i buy: http://www.ebay.co.uk/itm/330706284414?s...1423.l2649 Wasn't sure what the quality would be like, but 20k miles later and they're still going strong, so...
306 HDi Deathtrap - 130bhp / 220lbft
...UPGRADING...



Reply
Thanks given by:
Awesome. Cheers dude.
Reply
Thanks given by:
Boot badge looks good and I see you have some nice shiny boost pipes
[Image: mike_sig_zpsd438fb98.jpg]


Reply
Thanks given by:
Cheers bud.
Yup a bit of bling to add some zing. Got all the parts just need a spare day to get it done.
Reply
Thanks given by:
Well a bit of late night surprise expenditure but im pleased.

[Image: 20140110_185535_zpsxk5znyhc.jpg]

[Image: 20140110_185556_zpsrhu4nm7q.jpg]

Obviously the latter lot needs refurbing but they'll look awesome.
Reply
Thanks given by:
I think that you will need more pipes but good luck hope to see good things.
Bye Bye D-Turbo
Phase 1 GTi-6 now has a new owner
Rolling in the: Phase 3 HDI Wagon

The current estate project: http://306oc.co.uk/forum/thread-22237.html
Reply
Thanks given by:
Popped on the wheels today. Scrub like crazy. Need some spacers. At least 5 mm prob more like 10 tbh.

[Image: 20140111_115343_zpsai0ohewl.jpg]
Reply
Thanks given by:
Disaster has struck. It would seem that the alternator has died. Does anyone have one up for grabs. 2.0l hdi. Help!!
Reply
Thanks given by:


Possibly Related Threads…
Thread Author Replies Views Last Post
  Matts wagon Matt 21 7,625 19-01-2017, 09:28 PM
Last Post: ginge191
  Lewis's Moonstone Wagon LewisG 26 6,151 19-03-2015, 10:45 AM
Last Post: Toms306
  Project Daily Wagon! Y418AKH HDI Estate JamesG 44 15,510 06-05-2014, 08:36 PM
Last Post: JamesG

Forum Jump:


Users browsing this thread: 1 Guest(s)