Posts: 285
Threads: 72
Joined: Dec 2011
Reputation:
0
Location: Ireland
Car Model/Spec: 205 1.9 D Turbo (Full Gti Rep)
Thanks: 0
Given 1 thank(s) in 1 post(s)
10-01-2015, 11:13 AM
(This post was last modified: 10-01-2015, 02:44 PM by pugtk.)
How close those the flywheel sensor for the rev counter have to be be in order to pick up a reading
The reason being I put xud9 into my 205 and the rev counter those not work. I used the xud9 bracket for the sensor however the sensor could be closer to the flywheel
The rev counter was working before conversion.
Posts: 3,662
Threads: 127
Joined: Feb 2012
Reputation:
33
Location: London
Car Model/Spec: ZX Volcane TD
Thanks: 6
Given 32 thank(s) in 32 post(s)
When I fit them, I push the sensor right up against the flywheel then back it off just a fraction
Posts: 285
Threads: 72
Joined: Dec 2011
Reputation:
0
Location: Ireland
Car Model/Spec: 205 1.9 D Turbo (Full Gti Rep)
Thanks: 0
Given 1 thank(s) in 1 post(s)
17-01-2015, 05:59 PM
(This post was last modified: 17-01-2015, 06:04 PM by pugtk.)
I've tried various position of the sensor and still no luck.
Is there an earth for these?
It was working fine until I changed my engine and painted my bay.
Also my spots wont work after all this, hopefully an earth somewhere
Just to note.
The plug from the car has 2 wires and the plug from the sensor has 3 wires
Wondering now if I mixed sensors up?
Its on a 205 dturboo
Posts: 3,539
Threads: 42
Joined: Mar 2012
Reputation:
28
Thanks: 3
Given 89 thank(s) in 88 post(s)
which flywheel are you using?
should be a 1mm gap IIRC, new sensors come with tabs on the end which are 1mm tall so you just bung it in the hole till it touches and they wear off if there's any discrepancy in the flywheel.
Posts: 1,748
Threads: 41
Joined: Dec 2011
Reputation:
12
Location: Midlands
Car Model/Spec: Dtractor
Thanks: 0
Given 6 thank(s) in 6 post(s)
as said, they need to be ridiculously close to pick up. Put a blob of blue tack on the end, squash it into the hole then tighten. Blue tack will squidge off and hopefully leave it dead close.
Posts: 3,539
Threads: 42
Joined: Mar 2012
Reputation:
28
Thanks: 3
Given 89 thank(s) in 88 post(s)
yes, xud7 has a different clamp.
Posts: 285
Threads: 72
Joined: Dec 2011
Reputation:
0
Location: Ireland
Car Model/Spec: 205 1.9 D Turbo (Full Gti Rep)
Thanks: 0
Given 1 thank(s) in 1 post(s)
could this be causing the problem?
Does it mount it the same spot as the xud9?
Posts: 151
Threads: 19
Joined: Feb 2014
Reputation:
1
Location: Yorkshire Coast . . . :)
Car Model/Spec: 306d Estate on Biodiesel
Thanks: 0
Given 0 thank(s) in 0 post(s)
27-01-2015, 07:10 PM
(This post was last modified: 27-01-2015, 07:31 PM by Alex.)
I did a clutch change on mine some years ago, sensor never worked since. Possibly five years now without a rev counter.
Perhaps I'm too idle to be bothered by it.
![[Image: avatar_zpstlcgvhg8.jpg]](http://img.photobucket.com/albums/v363/toastmonster/avatar_zpstlcgvhg8.jpg){kind=avatar}
![[Image: 22f2b6b2-758b-4c1c-96fb-6fa9c6059b13_zpsf306b56b.jpg]](http://i585.photobucket.com/albums/ss299/Ha11elujaz0rs/22f2b6b2-758b-4c1c-96fb-6fa9c6059b13_zpsf306b56b.jpg)
