So iv done a little work on this now
1st job was to wip the beam out of the sigma
![[Image: 20121228_111312_zps445e735e.jpg]](http://i1038.photobucket.com/albums/a468/167gti8/20121228_111312_zps445e735e.jpg)
![[Image: 20121228_111346_zpsd2b37717.jpg]](http://i1038.photobucket.com/albums/a468/167gti8/20121228_111346_zpsd2b37717.jpg)
Then to wip the one piece exhaust off and the beam out of the 82k DT
![[Image: 20121228_133935_zpsf1dafc2c.jpg]](http://i1038.photobucket.com/albums/a468/167gti8/20121228_133935_zpsf1dafc2c.jpg)
82k beam with the gti6 bits in on the sigma
![[Image: 20121228_134019_zpsad723316.jpg]](http://i1038.photobucket.com/albums/a468/167gti8/20121228_134019_zpsad723316.jpg)
I also put the shagged beam back in ph2 to make it easyer to move it around.
Also noticed the heater matrix had been bypassed so it was defo dead , so out with the dash
![[Image: 20121230_141825_zps269286e7.jpg]](http://i1038.photobucket.com/albums/a468/167gti8/20121230_141825_zps269286e7.jpg)
![[Image: 20121230_141746_zpsa9add07b.jpg]](http://i1038.photobucket.com/albums/a468/167gti8/20121230_141746_zpsa9add07b.jpg)
Matrix out, suprise suprise it holds water like a colander .
![[Image: 20121230_141754_zpsadd68a18.jpg]](http://i1038.photobucket.com/albums/a468/167gti8/20121230_141754_zpsadd68a18.jpg)
![[Image: 20121230_141855_zpsfcdc09e2.jpg]](http://i1038.photobucket.com/albums/a468/167gti8/20121230_141855_zpsfcdc09e2.jpg)
Will go and get a new matrix tomorrow and put it back together
Also , my ph2 is a ABS bias valve moddle, and the ph1 was a non ABS non Bias valve moddle had a bit of a pain swapping brake lines about to make the ph2 beam work without a bias valve
1st job was to wip the beam out of the sigma
![[Image: 20121228_111312_zps445e735e.jpg]](http://i1038.photobucket.com/albums/a468/167gti8/20121228_111312_zps445e735e.jpg)
![[Image: 20121228_111346_zpsd2b37717.jpg]](http://i1038.photobucket.com/albums/a468/167gti8/20121228_111346_zpsd2b37717.jpg)
Then to wip the one piece exhaust off and the beam out of the 82k DT
![[Image: 20121228_133935_zpsf1dafc2c.jpg]](http://i1038.photobucket.com/albums/a468/167gti8/20121228_133935_zpsf1dafc2c.jpg)
82k beam with the gti6 bits in on the sigma
![[Image: 20121228_134019_zpsad723316.jpg]](http://i1038.photobucket.com/albums/a468/167gti8/20121228_134019_zpsad723316.jpg)
I also put the shagged beam back in ph2 to make it easyer to move it around.
Also noticed the heater matrix had been bypassed so it was defo dead , so out with the dash
![[Image: 20121230_141825_zps269286e7.jpg]](http://i1038.photobucket.com/albums/a468/167gti8/20121230_141825_zps269286e7.jpg)
![[Image: 20121230_141746_zpsa9add07b.jpg]](http://i1038.photobucket.com/albums/a468/167gti8/20121230_141746_zpsa9add07b.jpg)
Matrix out, suprise suprise it holds water like a colander .
![[Image: 20121230_141754_zpsadd68a18.jpg]](http://i1038.photobucket.com/albums/a468/167gti8/20121230_141754_zpsadd68a18.jpg)
![[Image: 20121230_141855_zpsfcdc09e2.jpg]](http://i1038.photobucket.com/albums/a468/167gti8/20121230_141855_zpsfcdc09e2.jpg)
Will go and get a new matrix tomorrow and put it back together
Also , my ph2 is a ABS bias valve moddle, and the ph1 was a non ABS non Bias valve moddle had a bit of a pain swapping brake lines about to make the ph2 beam work without a bias valve