Xantia inlet gasket
306oc - Peugeot 306 Owners Club & Forum › Engines › XUD Section v
Xantia inlet gasket

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Xantia inlet gasket
Frosty Offline
The Snowman
Moderators
Posts: 5,203
Threads: 110
Joined: Jan 2012
Reputation: 20
Location: Devon
Car Model/Spec: Estate, DT, GTI6 and 205
Facebook Instagram YouTube
Thanks: 1
Given 30 thank(s) in 30 post(s)
#1
19-06-2013, 06:12 AM
Should there be a gasket on a xantia inlet manifold where the elbow bit goes on for the pipe work. This is where I'm on about

[Image: null_zpsb9322a89.jpg]
Find
Reply
Thanks given by:
Piggy Offline
XUD Destroyer

Registered users - Donated
Posts: 20,092
Threads: 591
Joined: Nov 2012
Reputation: 54
Location: Cotswolds
Car Model/Spec: Stage 13 16v HDi
Facebook Instagram YouTube
Thanks: 22
Given 68 thank(s) in 68 post(s)
#2
19-06-2013, 06:16 AM
I would think so....

if not, flange sealant??
Wishes for more power...
YOUTUBE
Website Find
Reply
Thanks given by:
Jimbo Offline
Forgetful Na Na
Posts: 2,103
Threads: 122
Joined: Jan 2013
Reputation: 9
Location: south west, devon
Car Model/Spec: Kingfisher Ph1 Dturbo S
Thanks: 1
Given 7 thank(s) in 7 post(s)
#3
19-06-2013, 06:16 AM
You no there is you looked at mine. metal to metal wont seal 20 psi plus will it ...
Find
Reply
Thanks given by:
306Puggy Offline
Turbo fabricator extraordinaire!
Posts: 1,070
Threads: 115
Joined: Oct 2012
Thanks: 0
Given 0 thank(s) in 0 post(s)
#4
19-06-2013, 02:58 PM
Just sand both sides down smoothly with some 400 grit on a sanding block. Then it will seal.
Find
Reply
Thanks given by:
Grant Offline
Health and safety representative

Registered users - Donated
Posts: 5,847
Threads: 169
Joined: Dec 2011
Reputation: 91
Location: South London
Car Model/Spec: 2003 Jaguar S-Type Sport 3.0V6
Thanks: 1
Given 1 thank(s) in 1 post(s)
#5
19-06-2013, 03:02 PM
(19-06-2013, 02:58 PM)306Puggy Wrote: Just sand both sides down smoothly with some 400 grit on a sanding block. Then it will seal.


lmao
[Image: car-1.jpg]

Member of the 99% warning or you're nothing club


2000 Moonstone 1.8 Meridian - Sold
2000 China 3dr XS - Dead
1998 Diablo 3dr XSI
Find
Reply
Thanks given by:
Seb_Ryan Offline
Starting to Live for the 306
Posts: 1,417
Threads: 34
Joined: Dec 2011
Reputation: 8
Thanks: 0
Given 8 thank(s) in 8 post(s)
#6
19-06-2013, 03:08 PM
(19-06-2013, 03:02 PM)Grant Wrote:
(19-06-2013, 02:58 PM)306Puggy Wrote: Just sand both sides down smoothly with some 400 grit on a sanding block. Then it will seal.


lmao

lmao x2
Find
Reply
Thanks given by:
Jimbo Offline
Forgetful Na Na
Posts: 2,103
Threads: 122
Joined: Jan 2013
Reputation: 9
Location: south west, devon
Car Model/Spec: Kingfisher Ph1 Dturbo S
Thanks: 1
Given 7 thank(s) in 7 post(s)
#7
19-06-2013, 07:47 PM
(19-06-2013, 02:58 PM)306Puggy Wrote: Just sand both sides down smoothly with some 400 grit on a sanding block. Then it will seal.
Absolute tool!
Find
Reply
Thanks given by:
Piggy Offline
XUD Destroyer

Registered users - Donated
Posts: 20,092
Threads: 591
Joined: Nov 2012
Reputation: 54
Location: Cotswolds
Car Model/Spec: Stage 13 16v HDi
Facebook Instagram YouTube
Thanks: 22
Given 68 thank(s) in 68 post(s)
#8
19-06-2013, 08:08 PM
(19-06-2013, 03:08 PM)Seb_Ryan Wrote:
(19-06-2013, 03:02 PM)Grant Wrote:
(19-06-2013, 02:58 PM)306Puggy Wrote: Just sand both sides down smoothly with some 400 grit on a sanding block. Then it will seal.


lmao

lmao x2

lmao x3
Wishes for more power...
YOUTUBE
Website Find
Reply
Thanks given by:
ozonehostile Offline
Turning into a 306

Registered users - Donated
Posts: 5,946
Threads: 141
Joined: Oct 2012
Reputation: 35
Location: Herefordshire
Car Model/Spec: 106 rallye, GTi6, Hdi dturbo
Thanks: 3
Given 14 thank(s) in 14 post(s)
#9
19-06-2013, 11:17 PM
i just used some flange sealant for mine bud, holds fine at 25psi
Current stable
'09 Mercedes E320cdi wagon 
'99 306 gti6
Find
Reply
Thanks given by:
Mal Offline
Active Member
Posts: 199
Threads: 16
Joined: Mar 2013
Reputation: 0
Location: Meath
Car Model/Spec: 406TD/XUD Corolla/lolvan
Thanks: 0
Given 1 thank(s) in 1 post(s)
#10
20-06-2013, 01:20 PM
No just a rubber o ring. Avec la....
[Image: Image2547_zps43c71a3c.jpg]
[Image: Image423_zps1ac08bc4-1_zps15c76431.jpg]
Find
Reply
Thanks given by:
Jimbo Offline
Forgetful Na Na
Posts: 2,103
Threads: 122
Joined: Jan 2013
Reputation: 9
Location: south west, devon
Car Model/Spec: Kingfisher Ph1 Dturbo S
Thanks: 1
Given 7 thank(s) in 7 post(s)
#11
20-06-2013, 04:57 PM
He has a metal elbow so does not have the o ring
Find
Reply
Thanks given by:
Tom Offline
Living for the 205

Registered users - Donated
Posts: 6,482
Threads: 226
Joined: Dec 2011
Reputation: 24
Location: Cornwall
Car Model/Spec: A3 TDi
Thanks: 0
Given 0 thank(s) in 0 post(s)
#12
20-06-2013, 06:29 PM
Cut one out of cereal box lol? Bit of blue hylomar, job jobbed :p
Doesnt even own a 306.
Find
Reply
Thanks given by:
zx_volcane Offline
Living for the ZX

Registered users - Donated
Posts: 3,662
Threads: 127
Joined: Feb 2012
Reputation: 33
Location: London
Car Model/Spec: ZX Volcane TD
Thanks: 6
Given 32 thank(s) in 32 post(s)
#13
20-06-2013, 06:52 PM
I can vouch for a bit of gasket paper (cereal box) Smile
Team ZX

Arduino controlled huge turbo'd XUD'd ZX

^click for project

[Image: avatar_zpstlcgvhg8.jpg]
Find
Reply
Thanks given by:
Mal Offline
Active Member
Posts: 199
Threads: 16
Joined: Mar 2013
Reputation: 0
Location: Meath
Car Model/Spec: 406TD/XUD Corolla/lolvan
Thanks: 0
Given 1 thank(s) in 1 post(s)
#14
20-06-2013, 10:38 PM
(20-06-2013, 04:57 PM)Jimbo Wrote: He has a metal elbow so does not have the o ring

I have one with a metal elbow too, must check it when I have time and see what it has Wink
[Image: Image423_zps1ac08bc4-1_zps15c76431.jpg]
Find
Reply
Thanks given by:


Possibly Related Threads…
Thread Author Replies Views Last Post
  Fitting Xantia Inlet Nathan1305 7 2,407 10-04-2015, 12:13 PM
Last Post: Nathan1305
  Xantia manifold gasket Nathan1305 2 1,765 06-04-2015, 07:57 AM
Last Post: Nathan1305
  Inlet Manifold Gasket ally406 6 2,390 11-11-2013, 10:37 AM
Last Post: ally406

Forum Jump:


Users browsing this thread: 1 Guest(s)