+- 306oc - Peugeot 306 Owners Club & Forum (https://www.306oc.co.uk/forum)
+-- Forum: Engines (https://www.306oc.co.uk/forum/forumdisplay.php?fid=16)
+--- Forum: XUD Section (https://www.306oc.co.uk/forum/forumdisplay.php?fid=11)
+--- Thread: Xantia inlet gasket (/showthread.php?tid=14789)
Xantia inlet gasket - Frosty - 19-06-2013
Should there be a gasket on a xantia inlet manifold where the elbow bit goes on for the pipe work. This is where I'm on about
![[Image: null_zpsb9322a89.jpg]](http://i1065.photobucket.com/albums/u388/nufc4frosty/null_zpsb9322a89.jpg)
RE: Xantia inlet gasket - Piggy - 19-06-2013
I would think so....
if not, flange sealant??
RE: Xantia inlet gasket - Jimbo - 19-06-2013
You no there is you looked at mine. metal to metal wont seal 20 psi plus will it ...
RE: Xantia inlet gasket - 306Puggy - 19-06-2013
Just sand both sides down smoothly with some 400 grit on a sanding block. Then it will seal.
RE: Xantia inlet gasket - Grant - 19-06-2013
(19-06-2013, 02:58 PM)306Puggy Wrote: Just sand both sides down smoothly with some 400 grit on a sanding block. Then it will seal.
Re: RE: Xantia inlet gasket - Seb_Ryan - 19-06-2013
(19-06-2013, 03:02 PM)Grant Wrote:(19-06-2013, 02:58 PM)306Puggy Wrote: Just sand both sides down smoothly with some 400 grit on a sanding block. Then it will seal.
x2
RE: Xantia inlet gasket - Jimbo - 19-06-2013
(19-06-2013, 02:58 PM)306Puggy Wrote: Just sand both sides down smoothly with some 400 grit on a sanding block. Then it will seal.Absolute tool!
RE: Xantia inlet gasket - Piggy - 19-06-2013
(19-06-2013, 03:08 PM)Seb_Ryan Wrote:(19-06-2013, 03:02 PM)Grant Wrote:(19-06-2013, 02:58 PM)306Puggy Wrote: Just sand both sides down smoothly with some 400 grit on a sanding block. Then it will seal.
x3
RE: Xantia inlet gasket - ozonehostile - 19-06-2013
i just used some flange sealant for mine bud, holds fine at 25psi
RE: Xantia inlet gasket - Mal - 20-06-2013
No just a rubber o ring. Avec la....
![[Image: Image2547_zps43c71a3c.jpg]](http://i1225.photobucket.com/albums/ee388/humbrol/Image2547_zps43c71a3c.jpg)
RE: Xantia inlet gasket - Jimbo - 20-06-2013
He has a metal elbow so does not have the o ring
RE: Xantia inlet gasket - Tom - 20-06-2013
Cut one out of cereal box lol? Bit of blue hylomar, job jobbed :p
RE: Xantia inlet gasket - zx_volcane - 20-06-2013
I can vouch for a bit of gasket paper (cereal box)
RE: Xantia inlet gasket - Mal - 20-06-2013
(20-06-2013, 04:57 PM)Jimbo Wrote: He has a metal elbow so does not have the o ring
I have one with a metal elbow too, must check it when I have time and see what it has
