knocking at front of car

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
knocking at front of car
#1
Hi guys quick question I have a knocking noise from my engine bay on drivers side. The speed of knocking increases on acceleration. What could it be?

On a side note I have just done CAMBELT KIT and aux belt tensioner and idler could it be that is knocking
Got to love it when you have no ideaDodgy
Reply
Thanks given by:
#2
(18-02-2014, 11:45 PM)camoturd Wrote: Hi guys quick question I have a knocking noise from my engine bay on drivers side. The speed of knocking increases on acceleration. What could it be?

On a side note I have just done CAMBELT KIT and aux belt tensioner and idler could it be that is knocking

sounds like it mate, i wouldn't be driving it until you find out tbqh . .Smile
Phase 1 D-Turdo, K14@24 psi, De-cat, meaty backbox, Bosch pump, grinded LDA pin, duel air fed K&N =133.7bhp & 188ft/lbs
Reply
Thanks given by:
#3
Does it increase relative to engine speed or to road speed?
306 HDi Deathtrap - 130bhp / 220lbft
...UPGRADING...



Reply
Thanks given by:
#4
Engine speed
Got to love it when you have no ideaDodgy
Reply
Thanks given by:
#5
Get light between the engine and inner bay and see if anything is hitting
3 x Peugeot owner.

1996 106.
1996 306 D Turbo S.
1994 Mercedes Benz 320E.
1997 306 GLX.

Subscribe! - https://www.youtube.com/user/TheADKJD/videos
Reply
Thanks given by:
#6
Yeah its is strange if it was anywhere else I would of thought it was a tappet

Bit have noticed it starts at about 2500 rpm and dies at 4000 rpm and happens under heavy acceleration
Got to love it when you have no ideaDodgy
Reply
Thanks given by:
#7
Take aux belt off.

If noise dissapears then its on the aux setup
Wishes for more power...
Reply
Thanks given by:
#8
Ok will do that
Got to love it when you have no ideaDodgy
Reply
Thanks given by:
#9
Could be.injectors worn on hdi
Have a light tapping noise under load up until around 3200rpm usually?
I did changed injectors and.noise gone
[Image: av5ym8.jpg]
Reply
Thanks given by:
#10
(19-02-2014, 09:48 PM)Jimbo Wrote: Could be.injectors worn on hdi
Have a light tapping noise under load up until around 3200rpm usually?
I did changed injectors and.noise gone

Is that quiet a normal problem then
Got to love it when you have no ideaDodgy
Reply
Thanks given by:
#11
What youre describing sounds nothing like injectors.

It doesn't sound good though, is your crank pulley all good?
306 HDi Deathtrap - 130bhp / 220lbft
...UPGRADING...



Reply
Thanks given by:
#12
No idea how to tell if it's not
Got to love it when you have no ideaDodgy
Reply
Thanks given by:
#13
Sorry for the thread hijack but ive a knock from my front drivers well when turning, theres a couple of wee knocks when youve the wheel turned fully right and turning tight ie swinging the car round in a carpark my initial thought was droplinks?
Reply
Thanks given by:
#14
Could be CV joint if it only happens when turning.
Current Car: Lexus CT200h 1.8 138, 2013, 19,500 miles
Previous Car: VW Passat 2.0 TDi 140, 2005, 136,000 miles
Previous Car: Peugeot 306 XLdt (stock!), 150,000 miles (I miss this car Sad)
Reply
Thanks given by:
#15
Crank pulley yo.
Night Blue VW Golf 7 GTD : Bianca 306 Rallye : Mini Cooper D (The Mrs')
[Image: wallye-gtd.JPG?raw=1]
HDi Owner for 200k/9 years
Reply
Thanks given by:
#16
(20-02-2014, 12:15 PM)C2K Wrote: Crank pulley yo.

So are you saying it could be the crank pulley then?
Got to love it when you have no ideaDodgy
Reply
Thanks given by:
#17
Get the drivers side in the air and take the front wheel off. Have a look at the pulley with the engine running, if its knackered it'll wobble or run off-centre, there'll probably be rust marks and perishing too.
306 HDi Deathtrap - 130bhp / 220lbft
...UPGRADING...



Reply
Thanks given by:
#18
(20-02-2014, 04:35 PM)Poodle Wrote: Get the drivers side in the air and take the front wheel off. Have a look at the pulley with the engine running, if its knackered it'll wobble or run off-centre, there'll probably be rust marks and perishing too.

Ah fair enough I will do that when I change the wheels over as it 9 nay started after doing the aux tensioner and idler so it could be the crank pully as I changed the bolt that holds it on but not the pulley it's self
Got to love it when you have no ideaDodgy
Reply
Thanks given by:


Forum Jump:


Users browsing this thread: 7 Guest(s)