Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
WiNgNuTz's 407 SW
#24
(30-01-2016, 09:42 PM)Piggy Wrote: These aint bad to drive tbh.
I maintain one for a fwend.

Bottom ball joints/bearings are a common failure on the front...bit of a pig to do

And if the ball joints do go make sure you don't let them go on for too long as you'll be replacing the complete hub due to wear on the part of the hub the bearing part sits on.

Also ABS sensors seem to be a common issue on these, certainly not a bad old bus though these
Reply
Thanks given by:


Messages In This Thread
WiNgNuTz's 407 SW - by WiNgNuTz - 30-01-2016, 08:19 PM
RE: WiNgNuTz's 407 SW - by MY95 - 30-01-2016, 08:28 PM
RE: WiNgNuTz's 407 SW - by WiNgNuTz - 30-01-2016, 08:36 PM
RE: WiNgNuTz's 407 SW - by 1616six - 30-01-2016, 08:45 PM
RE: WiNgNuTz's 407 SW - by WiNgNuTz - 30-01-2016, 08:57 PM
RE: WiNgNuTz's 407 SW - by tigerstyle - 30-01-2016, 08:59 PM
RE: WiNgNuTz's 407 SW - by WiNgNuTz - 30-01-2016, 09:06 PM
RE: WiNgNuTz's 407 SW - by 1616six - 30-01-2016, 09:01 PM
RE: WiNgNuTz's 407 SW - by Toms306 - 31-01-2016, 09:10 AM
RE: WiNgNuTz's 407 SW - by MY95 - 30-01-2016, 09:06 PM
RE: WiNgNuTz's 407 SW - by MY95 - 30-01-2016, 09:18 PM
RE: WiNgNuTz's 407 SW - by WiNgNuTz - 30-01-2016, 09:26 PM
RE: WiNgNuTz's 407 SW - by MY95 - 30-01-2016, 09:32 PM
RE: WiNgNuTz's 407 SW - by Eeyore - 30-01-2016, 09:26 PM
RE: WiNgNuTz's 407 SW - by WiNgNuTz - 30-01-2016, 09:42 PM
RE: WiNgNuTz's 407 SW - by WiNgNuTz - 30-01-2016, 09:35 PM
RE: WiNgNuTz's 407 SW - by MY95 - 30-01-2016, 09:40 PM
RE: WiNgNuTz's 407 SW - by WiNgNuTz - 30-01-2016, 09:45 PM
RE: WiNgNuTz's 407 SW - by Piggy - 30-01-2016, 09:42 PM
RE: WiNgNuTz's 407 SW - by Frosty - 31-01-2016, 10:37 AM
RE: WiNgNuTz's 407 SW - by 7057sam - 31-01-2016, 03:14 AM
RE: WiNgNuTz's 407 SW - by cpikey316_ - 31-01-2016, 07:26 AM
RE: WiNgNuTz's 407 SW - by Redordead89 - 31-01-2016, 10:07 AM
RE: WiNgNuTz's 407 SW - by welshpug - 31-01-2016, 10:24 AM
RE: WiNgNuTz's 407 SW - by WiNgNuTz - 31-01-2016, 10:37 AM
RE: WiNgNuTz's 407 SW - by Frosty - 31-01-2016, 10:46 AM
RE: WiNgNuTz's 407 SW - by WiNgNuTz - 31-01-2016, 10:56 AM
RE: WiNgNuTz's 407 SW - by Danny Wideboy - 31-01-2016, 03:03 PM

Forum Jump:


Users browsing this thread: 2 Guest(s)