23-12-2014, 12:45 PM
Not really done much to this recently as ive been busy on the axle builds i have in. I have been struggling with cold starts in the morning, mainly due to cold foul on the plugs . I am using 8 grade plugs which i believe this is the cause but it still starts first time. I am going to try some 7's for the rest of the winter untill it warms up and haven spoken to sandy he agrees its worth a try.
Ive been trying out the gopro as ive not really used it since buying it, Managed to pull this screen shot from it.
![[Image: 6D2CDC69-B87F-4105-89D6-FC71E121D417_zps7n0l2nww.jpg]](http://i10.photobucket.com/albums/a129/skyline_999/205%20gti%20project/6D2CDC69-B87F-4105-89D6-FC71E121D417_zps7n0l2nww.jpg)
Being a complete yob!
Most of my attention has been focused on the 106 as its currently in for a respray as it was about 50 shades of red! I have a good friend who has kindly taken on the job in his spare time and having just taken a job with mclaren i have total faith in him. Also i have been designing a inlet manifold for it for a set of bodies.
![[Image: 639E1367-1FD4-4DF2-96A6-717F240E27DA_zpstvs7uaa9.jpg]](http://i10.photobucket.com/albums/a129/skyline_999/106%20gti/639E1367-1FD4-4DF2-96A6-717F240E27DA_zpstvs7uaa9.jpg)
![[Image: C63C86C2-37D5-4065-85CC-6A1803363AF3_zpsu5b7koxk.jpg]](http://i10.photobucket.com/albums/a129/skyline_999/106%20gti/C63C86C2-37D5-4065-85CC-6A1803363AF3_zpsu5b7koxk.jpg)
I do plan to drop the axle from the 205 after xmas and rebuild it again, hopefully with a bigger arb and fit a set of refurbed 32mm calipers and a bias valve.
Stef
Ive been trying out the gopro as ive not really used it since buying it, Managed to pull this screen shot from it.
![[Image: 6D2CDC69-B87F-4105-89D6-FC71E121D417_zps7n0l2nww.jpg]](http://i10.photobucket.com/albums/a129/skyline_999/205%20gti%20project/6D2CDC69-B87F-4105-89D6-FC71E121D417_zps7n0l2nww.jpg)
Being a complete yob!
Most of my attention has been focused on the 106 as its currently in for a respray as it was about 50 shades of red! I have a good friend who has kindly taken on the job in his spare time and having just taken a job with mclaren i have total faith in him. Also i have been designing a inlet manifold for it for a set of bodies.
![[Image: 639E1367-1FD4-4DF2-96A6-717F240E27DA_zpstvs7uaa9.jpg]](http://i10.photobucket.com/albums/a129/skyline_999/106%20gti/639E1367-1FD4-4DF2-96A6-717F240E27DA_zpstvs7uaa9.jpg)
![[Image: C63C86C2-37D5-4065-85CC-6A1803363AF3_zpsu5b7koxk.jpg]](http://i10.photobucket.com/albums/a129/skyline_999/106%20gti/C63C86C2-37D5-4065-85CC-6A1803363AF3_zpsu5b7koxk.jpg)
I do plan to drop the axle from the 205 after xmas and rebuild it again, hopefully with a bigger arb and fit a set of refurbed 32mm calipers and a bias valve.
Stef
