306oc - Peugeot 306 Owners Club & Forum › Engines › XUD Section v
Inlet Manifold Bolts

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Inlet Manifold Bolts
silverzx Offline
Always leaves skidz

Registered users - Donated
Posts: 4,926
Threads: 266
Joined: Dec 2011
Reputation: 18
Location: Somerset
Car Model/Spec: 205 DTurbo
Thanks: 73
Given 7 thank(s) in 7 post(s)
#5
22-08-2012, 08:32 PM
(22-08-2012, 08:26 PM)Dan! Wrote: Mindfuck. What you are describing is pretty much impossible mate. If 20mm is only just nipping up then 25mm should be fine, how can a stud be too long, the extra thread will just come out the back of the nut...

The 25's without the extra nut don't go in enough to press against the gasket. With a nut on it just spins freely/loosely once all the way in.

20's go all the way in to the gasket but dont nip up tight.

15's are too short (almost to even reach the threads in the block).

I guess you could get some 22.5's but my local "Nuts & Bolts" specialist only does them in increments of 5.

Guess I could just stick a load more washers on the 25's.

It might not even be leaking to be fair.
Supercharged GTi6 Build
S14 Zenki Build
[Image: signature.png]
Find
Reply
Thanks given by:


Messages In This Thread
Inlet Manifold Bolts - by silverzx - 22-08-2012, 07:19 PM
RE: Inlet Manifold Bolts - by ash23 - 22-08-2012, 07:35 PM
RE: Inlet Manifold Bolts - by Matt - 22-08-2012, 08:05 PM
Re: Inlet Manifold Bolts - by Dan! - 22-08-2012, 08:26 PM
RE: Inlet Manifold Bolts - by silverzx - 22-08-2012, 08:32 PM
RE: Inlet Manifold Bolts - by strictly_perv - 23-08-2012, 06:36 PM
RE: Inlet Manifold Bolts - by CJ_Derv - 22-08-2012, 08:44 PM
RE: Inlet Manifold Bolts - by Dave - 22-08-2012, 10:18 PM
RE: Inlet Manifold Bolts - by Joe - 23-08-2012, 08:49 AM
RE: Inlet Manifold Bolts - by silverzx - 23-08-2012, 09:53 AM
RE: Inlet Manifold Bolts - by Dave - 23-08-2012, 06:26 PM
RE: Inlet Manifold Bolts - by Dave - 23-08-2012, 06:46 PM
RE: Inlet Manifold Bolts - by CJ_Derv - 24-08-2012, 08:50 AM
RE: Inlet Manifold Bolts - by silverzx - 24-08-2012, 10:02 AM
RE: Inlet Manifold Bolts - by CJ_Derv - 24-08-2012, 10:07 AM

Possibly Related Threads…
Thread Author Replies Views Last Post
  Exhaust and inlet manifold spacers and studs andyyy 1 1,310 15-03-2015, 01:51 AM
Last Post: zx_volcane
  XUD Inlet manifold studs Tom 19 4,775 08-04-2014, 12:28 PM
Last Post: Ruan
  Inlet Manifold Gasket ally406 6 2,409 11-11-2013, 10:37 AM
Last Post: ally406

Forum Jump:


Users browsing this thread: 1 Guest(s)