Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Fitting conrods
#8
Gudgeon pins are held in with a circlip, prize out with a screwdriver and watch your face and also where it goes when it comes out then just push the pin out, piece of piss Smile

Just make sure you get the piston the correct way round on the rod as the indent in the bearing needs to be facing the correct way!

And as ginge says, make sure that you use plenty of lube, friction burns are never good lmao seriously though, a good coating of clean oil on everything as you assemble it should be fine until the oil gets circulating again.
Team Orange Engine Bay

My flickr photostream - http://www.flickr.com/photos/markairey
Reply
Thanks given by:


Messages In This Thread
Fitting conrods - by Ricky - 22-07-2012, 09:00 PM
RE: Fitting conrods - by Ricky - 23-07-2012, 06:52 PM
RE: Fitting conrods - by ash23 - 23-07-2012, 07:01 PM
RE: Fitting conrods - by Ricky - 24-07-2012, 06:31 AM
RE: Fitting conrods - by mark_airey - 24-07-2012, 07:12 AM
RE: Fitting conrods - by Ricky - 24-07-2012, 07:55 AM
RE: Fitting conrods - by ginge191 - 24-07-2012, 08:10 AM
RE: Fitting conrods - by mark_airey - 24-07-2012, 08:23 AM
RE: Fitting conrods - by ginge191 - 24-07-2012, 09:10 AM
RE: Fitting conrods - by Dave - 24-07-2012, 11:10 AM
RE: Fitting conrods - by Ruan - 24-07-2012, 12:50 PM
RE: Fitting conrods - by ginge191 - 24-07-2012, 12:54 PM
RE: Fitting conrods - by Ruan - 24-07-2012, 01:07 PM
RE: Fitting conrods - by ginge191 - 24-07-2012, 01:51 PM
RE: Fitting conrods - by mark_airey - 24-07-2012, 02:01 PM
RE: Fitting conrods - by CJ_Derv - 24-07-2012, 01:46 PM
RE: Fitting conrods - by samass - 24-07-2012, 01:55 PM
RE: Fitting conrods - by ginge191 - 24-07-2012, 02:01 PM
RE: Fitting conrods - by Ricky - 24-07-2012, 01:57 PM
RE: Fitting conrods - by Dave - 24-07-2012, 02:00 PM
RE: Fitting conrods - by samass - 24-07-2012, 02:03 PM
RE: Fitting conrods - by ginge191 - 24-07-2012, 02:08 PM
RE: Fitting conrods - by samass - 24-07-2012, 02:08 PM
RE: Fitting conrods - by ginge191 - 24-07-2012, 02:10 PM
RE: Fitting conrods - by mark_airey - 24-07-2012, 02:21 PM
RE: Fitting conrods - by ginge191 - 24-07-2012, 02:23 PM
RE: Fitting conrods - by mark_airey - 24-07-2012, 02:29 PM
RE: Fitting conrods - by Ruan - 24-07-2012, 03:50 PM
RE: Fitting conrods - by ginge191 - 24-07-2012, 07:41 PM
RE: Fitting conrods - by 4WayDiablo - 24-07-2012, 08:10 PM
RE: Fitting conrods - by ginge191 - 24-07-2012, 08:22 PM
RE: Fitting conrods - by mark_airey - 24-07-2012, 09:01 PM
RE: Fitting conrods - by ginge191 - 24-07-2012, 10:17 PM
RE: Fitting conrods - by InkedMuttley - 28-07-2012, 06:45 AM
RE: Fitting conrods - by mark_airey - 28-07-2012, 09:03 AM

Possibly Related Threads…
Thread Author Replies Views Last Post
  XUD7T and XUD9T suitable conrods? Biggen 1 1,517 08-02-2019, 06:38 PM
Last Post: Biggen
  XUD7, XUD9 and upgrade conrods assembled 4 2,345 10-07-2017, 10:20 AM
Last Post: Ruan
  D8A block and hdi conrods Teddy 16 4,926 15-11-2013, 07:53 AM
Last Post: Dave

Forum Jump:


Users browsing this thread: 1 Guest(s)