Posts: 15,646
Threads: 541
Joined: Dec 2011
Reputation:
124
Location: Aylesbury
Car Model/Spec: 320bhp Impreza WRX
Thanks: 7
Given 59 thank(s) in 58 post(s)
Anyone got any recommendations for a cheap but decent set of drill bits. I've been using wilko ones and they manage half the depth of a manifold stud before being blunt and it's really obvious as they fly through the first half and then just give up.
So where can I get some decent drill bits that won't break the bank and will last through drilling out half a dozen studs?
Posts: 13,881
Threads: 476
Joined: Dec 2011
Reputation:
81
Location: Ipswich
Car Model/Spec: 306 Rallye
Thanks: 4
Given 104 thank(s) in 102 post(s)
Ive been using my dads bosch set and need to get my own really. Ive snapped the 4.5, the 5 and now the 5.5 on metal so im not sure they are all that. :/
Maybe im just expecting too much. Have had them for a few years now. Im not entirely sure cheap and decent go together.
Posts: 1,484
Threads: 101
Joined: Jun 2015
Reputation:
2
Location: Oxfordshire
Car Model/Spec: 306HDi 90 LX
Thanks: 13
Given 28 thank(s) in 28 post(s)
I bought a set of these at the NEC bike show. used a couple, but not given them a 'full workout' yet.
http://www.drillalldrillbits.com/
It goes, it stops (as reqd). 
Hate Housework!
Posts: 1,791
Threads: 19
Joined: Jun 2012
Reputation:
12
Location: Devonshire
Car Model/Spec: Peugeot 309 GRD(T)
Thanks: 4
Given 25 thank(s) in 24 post(s)
Posts: 594
Threads: 25
Joined: Dec 2011
Reputation:
3
Location: Leeds
Car Model/Spec: Vectra & Berlingo
Thanks: 5
Given 5 thank(s) in 5 post(s)
I use Dorma bits, with out doubt the best if a little expensive. Any Cobalt set should do the job though?
Posts: 1,135
Threads: 14
Joined: May 2012
Reputation:
7
Location: Sheffield
Thanks: 0
Given 5 thank(s) in 5 post(s)
Yea I got a Cobalt set off eBay, it's lasted ages, only a few have snapped.
Posts: 4,604
Threads: 90
Joined: Dec 2011
Reputation:
54
Location: Cornwall
Car Model/Spec: 1996 306 DT M-TDI/16
Thanks: 0
Given 20 thank(s) in 18 post(s)
http://www.ebay.co.uk/itm/BERGEN-Tools-1...SwMNxXYxEa
Cheap, and last very well for what they cost. Key is cutting fluid / spray, and ideally a pillar drill, operator is as important as the bit....
| Dyno Power Runs & Steady State Facilities Available, Just Ask Anytime |
| #DervMafia |
![[Image: sigi-2.png]](http://i281.photobucket.com/albums/kk226/darrenjlobb/sigi-2.png)
Posts: 13,881
Threads: 476
Joined: Dec 2011
Reputation:
81
Location: Ipswich
Car Model/Spec: 306 Rallye
Thanks: 4
Given 104 thank(s) in 102 post(s)
(24-03-2017, 12:58 PM)darrenjlobb Wrote: http://www.ebay.co.uk/itm/BERGEN-Tools-1...SwMNxXYxEa
Cheap, and last very well for what they cost. Key is cutting fluid / spray, and ideally a pillar drill, operator is as important as the bit....
totally worth getting those. Look at how many there are to snap! 
Posts: 5,946
Threads: 141
Joined: Oct 2012
Reputation:
35
Location: Herefordshire
Car Model/Spec: 106 rallye, GTi6, Hdi dturbo
Thanks: 3
Given 14 thank(s) in 14 post(s)
Dormer and wurth are the best bits you can get. Reca make fairly decent ones too. Cheap drill bits are just a false economy really
Current stable
'09 Mercedes E320cdi wagon
'99 306 gti6
Posts: 391
Threads: 29
Joined: Sep 2014
Reputation:
0
Thanks: 1
Given 7 thank(s) in 7 post(s)
buy decent bits, buy drill bit sharpener.
Posts: 338
Threads: 20
Joined: Sep 2013
Reputation:
0
Location: north east
Car Model/Spec: gti 5 Turbo
Thanks: 0
Given 2 thank(s) in 2 post(s)
I bought a draper set still going strong
if you look out on ebay job lots of wurth and dormers are on there regualry
Posts: 659
Threads: 206
Joined: Feb 2012
Reputation:
3
Location: far away
Car Model/Spec: 3dr dt-s
Thanks: 1
Given 0 thank(s) in 0 post(s)
toolstation do cobalt double packs quite cheaply, go up to 13mm.
I have 2 of each as I am fed up using standard "black" drillbits....(dormer or presto--not shite stuff)
Posts: 15,646
Threads: 541
Joined: Dec 2011
Reputation:
124
Location: Aylesbury
Car Model/Spec: 320bhp Impreza WRX
Thanks: 7
Given 59 thank(s) in 58 post(s)
Cheers guys, got some choices to make now.
Posts: 2,140
Threads: 128
Joined: May 2014
Reputation:
21
Location: Cardiff
Car Model/Spec: Stage3 HDi RHF5@25psi 174bhp
Thanks: 1
Given 41 thank(s) in 38 post(s)
(24-03-2017, 10:49 AM)Dum-Dum Wrote: Anyone got any recommendations for a cheap but decent set of drill bits. I've been using wilko ones and they manage half the depth of a manifold stud before being blunt and it's really obvious as they fly through the first half and then just give up.
So where can I get some decent drill bits that won't break the bank and will last through drilling out half a dozen studs?
There is rarely such a thing mate.,,, buy cheap and buy twice..
Cheap drill bits generally tend to be just that.. cheap. Tungsten carbide tipped ones rarely are Properly tipped unless you spend big pennies
My advice would be to get down to RS or somewhere of the sort and pick up a nice set of black oxide or suitably coated HSS drill bits..
i have a nice RS set (that didnt break the bank) and have only broken the ones i have been stupid with..
https://www.youtube.com/watch?v=GYpMf0ahJNc This guy has a couple of PhDs and i have been addicted to his videos for a while, works in the mining and oil industry and is . Notice the difference between cheap and expensive.
been watching him for a while and learnt some nice little tricks..
Given the choice between Niall and the sheep. I would choose the sheep!
/Toseland
Posts: 440
Threads: 8
Joined: Jun 2013
Reputation:
1
Location: South Shroshire
Car Model/Spec: 405 SRDT
Thanks: 1
Given 6 thank(s) in 6 post(s)
Some pretty good advice on this thread tbh. Plenty of lube and the correct speed make all the difference ime. If drilling with a pistol drill I find drills I have sharpened myself with a more aggressive pitch normally drill better. A bench grinder is ideal for that obviously but have used an angle grinder when out on site if stuck. The key is grinding away enough relief at the back of the cutting edge to let the swarf escape.
As for buying cheap, buy twice that's an understatement for some drill bits, there is some truly dreadful shite out there!
Posts: 120
Threads: 10
Joined: Feb 2015
Reputation:
0
Location: Dumfries
Car Model/Spec: Estate
Thanks: 1
Given 0 thank(s) in 0 post(s)
Country: 
This is exactly the thread I needed since I need to drill out a bolt that has completely seized, just ordered some dorma bits from amazon and some cutting compound. Hopefully those will do the trick, fingers crossed.
Posts: 3,539
Threads: 42
Joined: Mar 2012
Reputation:
28
Thanks: 3
Given 89 thank(s) in 88 post(s)
its Dormer not dorma.
but yes, I would recommend that brand.
Posts: 255
Threads: 18
Joined: Mar 2016
Reputation:
0
Location: perth
Car Model/Spec: Fabia 1.9tdi 105 PD
Thanks: 0
Given 5 thank(s) in 5 post(s)
Just a reminder that if anybody uses Cobalt drills - eye protection is essential !
Posts: 120
Threads: 10
Joined: Feb 2015
Reputation:
0
Location: Dumfries
Car Model/Spec: Estate
Thanks: 1
Given 0 thank(s) in 0 post(s)
Country:
(27-03-2017, 04:29 PM)welshpug Wrote: its Dormer not dorma.
but yes, I would recommend that brand.
Yeah my bad, I just mispelled it but it's Dormer that I bought.
Posts: 1,950
Threads: 55
Joined: Dec 2011
Reputation:
17
Location: Rotherham
Car Model/Spec: 406 V6
Thanks: 3
Given 10 thank(s) in 10 post(s)
I use those 170pc cheap sets Darren recommended for random jobs. They're fine if you're not a moron on the drill trigger and burn them out. Hell, I used to use them in the CNC mill @ 9krpm...
But for proper jobs which need to be on size or for tapping, I have a set of Clarkson and Osborne - 135*, split point, with Ti-N coated flutes and TiAlN coated shoulder - which go through even hardened stuff like butter.
Custom roll cages/shiny suspension bits/general fabrication work undertaken, PM me.
Top engine mount repair/reinforcement/chocking for cracked chassis and high powered cars, drive in, drive out, 2 hour turnaround.
Posts: 1,748
Threads: 41
Joined: Dec 2011
Reputation:
12
Location: Midlands
Car Model/Spec: Dtractor
Thanks: 0
Given 6 thank(s) in 6 post(s)
I bought a real cheap set off ebay that were HSS, havent had any issues with them for the small bits of drilling I do, as mentioned above technique plays a huge part in not f*cking them, steady hand, oiling the cut and going slow mine are all still good.
|
![[Image: 22f2b6b2-758b-4c1c-96fb-6fa9c6059b13_zpsf306b56b.jpg]](http://i585.photobucket.com/albums/ss299/Ha11elujaz0rs/22f2b6b2-758b-4c1c-96fb-6fa9c6059b13_zpsf306b56b.jpg)