Hose sizes
306oc - Peugeot 306 Owners Club & Forum › Engines › XUD Section v
Hose sizes

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Hose sizes
cwspellowe Offline
Lad of the Norf
Posts: 4,883
Threads: 198
Joined: Jan 2012
Reputation: 135
Location: Not near you
Thanks: 0
Given 0 thank(s) in 0 post(s)
#1
24-04-2012, 09:47 PM
Evening fellas, does someone fancy letting me know the common hose sizes in the engine bay? ie. fuel lines, boost compensator etc? Thinking of buying new and cutting to length rather than hunting for standard used ones.
[Image: signature_zps1a02ba79.jpg]
Find
Reply
Thanks given by:
ginge191 Offline
Professional Jungle Ginger

Registered users - Donated
Posts: 8,019
Threads: 374
Joined: Dec 2011
Reputation: 38
Location: Isle of Wight
Car Model/Spec: GTI 6
Thanks: 8
Given 16 thank(s) in 14 post(s)
#2
24-04-2012, 09:50 PM
For the life of me i can't remember the size, but know buying from ebay, altogether it cost me about £10. the return line's is the only different size you need.
compensator and filter hose are the same iirc
Diablo Hdi Dturbo and 205 1.9 project - it lives!
Find
Reply
Thanks given by:
cwspellowe Offline
Lad of the Norf
Posts: 4,883
Threads: 198
Joined: Jan 2012
Reputation: 135
Location: Not near you
Thanks: 0
Given 0 thank(s) in 0 post(s)
#3
24-04-2012, 09:59 PM
Think it's about 10mm, and fuel lines are about 8mm?
[Image: signature_zps1a02ba79.jpg]
Find
Reply
Thanks given by:
Ruan Offline
"Gearbox Side" towards engine 4 lyf

Registered users - Donated
Posts: 5,205
Threads: 91
Joined: Dec 2011
Reputation: 83
Location: Oxfordshire/Cornwall
Car Model/Spec: Moonstone DT/Volvo V50
Thanks: 2
Given 41 thank(s) in 41 post(s)
#4
24-04-2012, 11:15 PM
6-8mm... If you buy silicon pipes you can make it all fit, I've got 6mm everywhere and it fits, you might just have to use a bit of lube to get it over some stuff...
(16-05-2016, 10:45 AM)Toms306 Wrote: Oh I don't care about the stripped threads lol, that's easily solved by hammering the bolt in. Wink
Nanstone GTD5 GT17S - XUD9TE
Volvo V50 D5 R-Design SE Sport - Daily cruise wagon.
Find
Reply
Thanks given by:
cwspellowe Offline
Lad of the Norf
Posts: 4,883
Threads: 198
Joined: Jan 2012
Reputation: 135
Location: Not near you
Thanks: 0
Given 0 thank(s) in 0 post(s)
#5
25-04-2012, 10:26 AM
If I went for 8mm all round it should clamp to the smaller stuff ok, right? Also the vacuum hose from pump to servo, 10mm?
[Image: signature_zps1a02ba79.jpg]
Find
Reply
Thanks given by:
Ruan Offline
"Gearbox Side" towards engine 4 lyf

Registered users - Donated
Posts: 5,205
Threads: 91
Joined: Dec 2011
Reputation: 83
Location: Oxfordshire/Cornwall
Car Model/Spec: Moonstone DT/Volvo V50
Thanks: 2
Given 41 thank(s) in 41 post(s)
#6
25-04-2012, 11:36 AM
Aye yeah.

I think vac pump to servo is 10mm aye.
(16-05-2016, 10:45 AM)Toms306 Wrote: Oh I don't care about the stripped threads lol, that's easily solved by hammering the bolt in. Wink
Nanstone GTD5 GT17S - XUD9TE
Volvo V50 D5 R-Design SE Sport - Daily cruise wagon.
Find
Reply
Thanks given by:
ginge191 Offline
Professional Jungle Ginger

Registered users - Donated
Posts: 8,019
Threads: 374
Joined: Dec 2011
Reputation: 38
Location: Isle of Wight
Car Model/Spec: GTI 6
Thanks: 8
Given 16 thank(s) in 14 post(s)
#7
25-04-2012, 11:47 AM
Fuel hose from filter to pump - http://www.ebay.co.uk/itm/8mm-5-16-R6-F ... 1e60432d8b

and leak off piping - http://www.ebay.co.uk/itm/DIESEL-LEAK-S ... 564688ab7c

found it.. Also posted in project thread. This was what I bought, was enough plus spares
Diablo Hdi Dturbo and 205 1.9 project - it lives!
Find
Reply
Thanks given by:


Forum Jump:


Users browsing this thread: 1 Guest(s)