Another bottom arm fails
|
Another bottom arm fails
|
Posts: 5,203
Threads: 110 Joined: Jan 2012 Reputation: 20 Location: Devon Car Model/Spec: Estate, DT, GTI6 and 205 
Thanks: 1
Given 30 thank(s) in 30 post(s)
07-09-2013, 07:11 PM
Jimbo had a bottom arm go on his HDi the other day. We sorted it out this morning but here is the arm
![[Image: null_zps265d8f33.jpg]](http://s1065.photobucket.com/user/nufc4frosty/media/null_zps265d8f33.jpg.html) ![[Image: null_zpsea642b9c.jpg]](http://s1065.photobucket.com/user/nufc4frosty/media/null_zpsea642b9c.jpg.html) Another high quality after market arm it would seem to be 
Posts: 20,092
Threads: 591 Joined: Nov 2012 Reputation: 54 Location: Cotswolds Car Model/Spec: Stage 13 16v HDi
Thanks: 22
Given 68 thank(s) in 68 post(s) 
07-09-2013, 10:41 PM
I've never seen the front bush detach like that. I know the P-bush is prone to removing itself, but jeeeez, that coulda been awful!
![[Image: car-1.jpg]](http://i1117.photobucket.com/albums/k591/grant-306/car-1.jpg) Member of the 99% warning or you're nothing club 2000 Moonstone 1.8 Meridian - Sold 2000 China 3dr XS - Dead 1998 Diablo 3dr XSI 
Snap, this one only lasted a few weeks too, Fitted by a MOT garage,
![[Image: IMG_1075.jpg]](http://s940.photobucket.com/user/pugracing/media/IMG_1075.jpg.html) But for £20.00 what can you expect 
07-09-2013, 11:39 PM
Good old cheap chinese shite.
Custom roll cages/shiny suspension bits/general fabrication work undertaken, PM me.
Top engine mount repair/reinforcement/chocking for cracked chassis and high powered cars, drive in, drive out, 2 hour turnaround.
Posts: 20,092
Threads: 591 Joined: Nov 2012 Reputation: 54 Location: Cotswolds Car Model/Spec: Stage 13 16v HDi
Thanks: 22
Given 68 thank(s) in 68 post(s)
07-09-2013, 11:39 PM
who cares if it was a fiver or fifty quid...if thats the price they choose to sell it at, fine. But its no excuse to make suspension from old cheese.
people say, 'I dont mind if it breaks, it was cheap'...no, I do mind. Cheap or expensive, it should be fit for purpose Wishes for more power...
08-09-2013, 06:45 AM
Holy f*ck that's horrendous! Letter to the manufacturer?
Posts: 20,092
Threads: 591 Joined: Nov 2012 Reputation: 54 Location: Cotswolds Car Model/Spec: Stage 13 16v HDi
Thanks: 22
Given 68 thank(s) in 68 post(s)
08-09-2013, 07:18 AM
I also hate those coz they rivet the ruddy ball joint in.
so if the bushes do last a decent time and ya ball joint goes, you spend ages grinding the sod out Wishes for more power...
08-09-2013, 10:15 AM
Mine did this in my miami blue ph1.. wheel came off and f*cked quite abit.. was a good job I was only doind 15mph.
Only the balljoint stayed in btw 
08-09-2013, 01:05 PM
I've seen too many fail like this. Often on 206's when often as not the whole wheel and hub comes away, leaving the car beached on it's subframe.
Welding and fabrication projects undertaken, contact me for more information.
08-09-2013, 01:16 PM
Shiiiiit, what if that happened at 70mph on a motorway full of traffic!
Posts: 6,367
Threads: 87 Joined: Dec 2011 Reputation: 48 Location: South Yorks. Car Model/Spec: Rouge vallelunga 5 door Dturbo 
Thanks: 2
Given 74 thank(s) in 70 post(s)
08-09-2013, 02:14 PM
could do with knowing where they were from so no-one else buys them tbh . . . .
Phase 1 D-Turdo, K14@24 psi, De-cat, meaty backbox, Bosch pump, grinded LDA pin, duel air fed K&N =133.7bhp & 188ft/lbs
08-09-2013, 03:51 PM
(This post was last modified: 08-09-2013, 03:51 PM by bigtone0777.)
Like Tom said it don't matter what price it was, that could have cost life worse case scenario =-O Just imagine that at 70 mph sending the car into oncoming traffic. There's no excuse for that kind of rubbish being sold!
08-09-2013, 07:53 PM
No comeback really, what Eastern produced item really cares about being fit for purpose, There's allot more products on the market like this you will be surprised.
08-09-2013, 08:11 PM
This reminds me I need to check the shit the garage put on my brothers car. Probably junk like this.
Night Blue VW Golf 7 GTD : Bianca 306 Rallye : Mini Cooper D (The Mrs')
![[Image: wallye-gtd.JPG?raw=1]](https://www.dropbox.com/s/pcxk1pgpaucznvr/wallye-gtd.JPG?raw=1) HDi Owner for 200k/9 years
08-09-2013, 08:15 PM
(08-09-2013, 07:53 PM)miles Wrote: No comeback really, what Eastern produced item really cares about being fit for purpose, There's allot more products on the market like this you will be surprised. Surely they have to meet a British Standard to be sold over here though? Obviously not if they're a Chinese ebay shop though lol.
08-09-2013, 08:20 PM
None at all, Some parts I have been given to fit don;t even work from new, No standard as far as I know
Overall Road Going Production Class Winner at BARC Gurston Down Speed Hillclimb 2012, 2013 & 2014 With a class record along the way (For a while), Taking 2nd place will be Ian Redding's 306 GTi
2016 Castle Combe GT championship class winner
Posts: 5,203
Threads: 110 Joined: Jan 2012 Reputation: 20 Location: Devon Car Model/Spec: Estate, DT, GTI6 and 205
Thanks: 1
Given 30 thank(s) in 30 post(s)
08-09-2013, 08:30 PM
09-09-2013, 09:24 AM
Yeah it was 60mph ish wheel folded under the arch. Skidded to a halt on a busy main road managed to ditch it in a layby.
After only having the car a week it put me off somewhat. Had no idea that it had cheap arms fitted and certainty will check on any other cars from now . Had to replace Driveshaft Arm Balljoint Arb link P bush. Somehow it disnt actually damage the wing too bad. Id say luck was on my side could have been very nasty ![[Image: av5ym8.jpg]](http://i59.tinypic.com/av5ym8.jpg)
09-09-2013, 12:46 PM
Managed to get it into a layby with half the front end hanging off?? Fair play mucker, got to respect that lol!
Posts: 5,203
Threads: 110 Joined: Jan 2012 Reputation: 20 Location: Devon Car Model/Spec: Estate, DT, GTI6 and 205
Thanks: 1
Given 30 thank(s) in 30 post(s)
09-09-2013, 12:59 PM
09-09-2013, 03:11 PM
(09-09-2013, 03:06 PM)Tom Wrote: Bet that scared the f*ck out of you! Haha!Yeah its not something I would recommend mate lol Proper shit scary stuff Got my arch rolled for free maybe its a sign to go low
|
|
« Next Oldest | Next Newest »
|
![[Image: 20130905_181657-1.jpg]](http://i679.photobucket.com/albums/vv153/jim-bob1991/20130905_181657-1.jpg)
![[Image: 20130905_174216.jpg]](http://i679.photobucket.com/albums/vv153/jim-bob1991/20130905_174216.jpg)
