306oc - Peugeot 306 Owners Club & Forum
Half leather phz2 in a phz3 air bags? resistor? - Printable Version

+- 306oc - Peugeot 306 Owners Club & Forum (https://www.306oc.co.uk/forum)
+-- Forum: 306 Repairs & Mods (https://www.306oc.co.uk/forum/forumdisplay.php?fid=22)
+--- Forum: Interior, Exterior, ICE (https://www.306oc.co.uk/forum/forumdisplay.php?fid=12)
+--- Thread: Half leather phz2 in a phz3 air bags? resistor? (/showthread.php?tid=2945)



Half leather phz2 in a phz3 air bags? resistor? - MattDM306 - 22-04-2012

im swapping phz three interior for phz2 half leather in way better condition than my ripped and torn interior, the only problem is my interior has side airbags and this one doesnt so what can i do to get around the air bag light that i will inevitably get like my abs light that wont turn off lol.


Re: Half leather phz2 in a phz3 air bags? resistor? - cully - 22-04-2012

1.5 to 2 Ohm resistor in sieres with a 2amp fuse


Half leather phz2 in a phz3 air bags? resistor? - Matt - 22-04-2012

Cully little bit more info, how do you do this?


Re: Half leather phz2 in a phz3 air bags? resistor? - cully - 22-04-2012

hope this helps


Half leather phz2 in a phz3 air bags? resistor? - Matt - 22-04-2012

Ahhh so this is using the wiring under the seat? I think my air bag light must be on constantly as the bulb was removed by previous owner. I have s16 seats in mine guess the previous seats had side airbags. Will this need doing both sides?


Re: Half leather phz2 in a phz3 air bags? resistor? - cully - 22-04-2012

yes needs doing at each airbag you disconnect


Half leather phz2 in a phz3 air bags? resistor? - Matt - 22-04-2012

Sweet which ones are the air bag ones again? Will get this done, instead of cutting wires could you use the male spade connectors? Not keen on cutting the wiring


Re: Half leather phz2 in a phz3 air bags? resistor? - WiNgNuTz - 22-04-2012

Don't mean to hijack your thread Matt, but would this also work in reverse, I.e. ph3 seats with side airbags in a ph2 without? My airbag light has been flashing at me since I put the seats in.


Re: Half leather phz2 in a phz3 air bags? resistor? - MattDM306 - 22-04-2012

No worries wingnuts im sat watchin paint dry. will upload photos soon


Re: Half leather phz2 in a phz3 air bags? resistor? - Niall - 22-04-2012

WiNgNuTz Wrote:Don't mean to hijack your thread Matt, but would this also work in reverse, I.e. ph3 seats with side airbags in a ph2 without? My airbag light has been flashing at me since I put the seats in.

Flashing airbag light is pretensioners. There not connected properly.


Half leather phz2 in a phz3 air bags? resistor? - Matt - 22-04-2012

I don't even have a airbag light Wink


Re: Half leather phz2 in a phz3 air bags? resistor? - Niall - 22-04-2012

Matt Wrote:I don't even have a airbag light Wink

Mot fail!


Re: Half leather phz2 in a phz3 air bags? resistor? - Eeyore - 22-04-2012

Theres your answer then Matt! Get the stuff and ive got solder and heatshrink we can use! Smile


Half leather phz2 in a phz3 air bags? resistor? - Matt - 22-04-2012

Niall Wrote:
Matt Wrote:I don't even have a airbag light Wink

Mot fail!

I know that's why I need to sort mine Smile


Re: Half leather phz2 in a phz3 air bags? resistor? - 4WayDiablo - 22-04-2012

Niall Wrote:
Matt Wrote:I don't even have a airbag light Wink

Mot fail!
how are they gunna know if theres a bulb in there or not? (or are they supposed to come on ignition stage?)


Re: Half leather phz2 in a phz3 air bags? resistor? - cully - 22-04-2012

yes the lamp comes on as part of system check when the ign is switched on


Half leather phz2 in a phz3 air bags? resistor? - Matt - 22-04-2012

Lamp comes on for 3-4 seconds, as does the abs ninja


Re: Half leather phz2 in a phz3 air bags? resistor? - MattDM306 - 22-04-2012

My ans stays on all the time. have u got any fluxx sam? I have solder and soldering iron.wat fuse and resistors should i use?


Half leather phz2 in a phz3 air bags? resistor? - Matt - 22-04-2012

Abs sensor is gone I would presume and cully mentioned up there what bits to use Wink


Re: Half leather phz2 in a phz3 air bags? resistor? - MattDM306 - 23-04-2012

Its my mobile jidkng bits from me soz grr


Re: Half leather phz2 in a phz3 air bags? resistor? - devils_fuel - 23-04-2012

Niall Wrote:
Matt Wrote:I don't even have a airbag light Wink

Mot fail!


That's why I need your pretensioners srowell, ones gone off and airbag light flashing.

4way, they test ignition lights, Tim checked mine at MOT and said it would fail next year as the system tests its self and light goes out if the system is ok, hence I need pretensioners as ones gone off


Re: Half leather phz2 in a phz3 air bags? resistor? - Eeyore - 23-04-2012

MattDM306 Wrote:My ans stays on all the time. have u got any fluxx sam? I have solder and soldering iron.wat fuse and resistors should i use?

Dont need flux Smile