+- 306oc - Peugeot 306 Owners Club & Forum (https://www.306oc.co.uk/forum)
+-- Forum: 306 Repairs & Mods (https://www.306oc.co.uk/forum/forumdisplay.php?fid=22)
+--- Forum: Interior, Exterior, ICE (https://www.306oc.co.uk/forum/forumdisplay.php?fid=12)
+--- Thread: Xud exhaust (/showthread.php?tid=16034)
Xud exhaust - Matt - 31-07-2013
I want a straight through on the dt, and I'm getting impatient.
Having a decat - mid box - mid box is straight through right?
Or did I miss something with these backboxmidbox swap around?
Or what's the cheapest way to straight through? Over the counter parts? Welder? Silicon pipes and exhaust?
Also what's the standard width of a dt exhaust?
RE: Xud exhaust - Jonny81191 - 31-07-2013
(31-07-2013, 06:08 PM)Matt Wrote: I want a straight through on the dt, and I'm getting impatient.
Having a decat - mid box - mid box is straight through right?
Or did I miss something with these backboxmidbox swap around?
Or what's the cheapest way to straight through? Over the counter parts? Welder? Silicon pipes and exhaust?
Also what's the standard width of a dt exhaust?
Oh Matt..
RE: Xud exhaust - vlj - 31-07-2013
Silicone pipes? For an exhaust?
RE: Xud exhaust - Matt - 31-07-2013
Samass' genius idea haha
RE: Xud exhaust - Tom - 31-07-2013
Omg really?
RE: Xud exhaust - Mitch - 31-07-2013
Have a look in my project thread, i had a full straight through exhaust made from the turbo back at AA silencers in Stafford, if your anywhere near there? was only 86 pounds anyway
RE: Xud exhaust - Matt - 31-07-2013
Nah I'm on the Isle of Wight, welders and resources are low. It's a shit tonne harder to get anything done here!
RE: Xud exhaust - samass - 31-07-2013
yep silicone was my idea, mainly cuz that's all i had lying around and couldnt be arsed doing it properly, it was at the back, and its rated to 200 degrees anyway, it worked.
also matt, f*cking fail, exhaust in the interior section? noob
RE: Xud exhaust - Dum-Dum - 31-07-2013
Is your back box the type with the hanger that goes all the way round in squiggles (so you could knock it off in 1 piece)?
If it is get a mid section (on of the xantias has a mid with no box), knock the hangar off the standard box, get a massive jubilee to tie the midsection to the hangar and cut to the appropriate length.
No need for welding or complicated tools.
Also as Samass says; learn to forum noob
RE: Xud exhaust - Matt - 01-08-2013
It's in interior/exterior and ice, last time I checked, exhaust was exterior.
It's just the backbox really, xantia had a straight through mid? Does it Fit the same as a 306 mid? More or less the same design?
RE: Xud exhaust - Carlos182 - 01-08-2013
405 has a straight through mid AFAIK too.
RE: Xud exhaust - Dum-Dum - 01-08-2013
Its pretty much the same but different. However you could use it to make a straight through back box.
RE: Xud exhaust - Curt - 01-08-2013
(01-08-2013, 08:30 PM)Dum-Dum Wrote: Its pretty much the same but different.
Brilliant.
RE: Xud exhaust - Jonny81191 - 01-08-2013
Chris you're a special one aren't you..