![]() |
306 FMIC FAQ - Printable Version +- 306oc - Peugeot 306 Owners Club & Forum (https://www.306oc.co.uk/forum) +-- Forum: 306 Repairs & Mods (https://www.306oc.co.uk/forum/forumdisplay.php?fid=22) +--- Forum: Guides (https://www.306oc.co.uk/forum/forumdisplay.php?fid=9) +--- Thread: 306 FMIC FAQ (/showthread.php?tid=8172) |
RE: 306 FMIC FAQ - silverzx - 12-10-2013 Yeah, going under radiators is never a good shout... RE: 306 FMIC FAQ - Midnightclub - 12-10-2013 Should have looped it over the top like we did on ours, acts like a twin pass setup RE: 306 FMIC FAQ - maguire1992 - 12-10-2013 Thought about it but didn't want to do any cutting I'd say it will be fine Thanks for your comment RE: 306 FMIC FAQ - Midnightclub - 12-10-2013 We didn't have to cut anything, it fits like oem RE: 306 FMIC FAQ - silverzx - 12-10-2013 HDi's have plenty of room for pipe to go around either side of the radiator. RE: 306 FMIC FAQ - Poodle - 12-10-2013 Lol, yeah if you're using 1.5" pipes. The offside gap is about 45mm at it's widest point, that's why so many people go twin-pass. RE: 306 FMIC FAQ - Piggy - 12-10-2013 I went up and over with one side and cut the slam a wee bit RE: 306 FMIC FAQ - maguire1992 - 13-10-2013 My pipe was 2.5" so it was the handiest route RE: 306 FMIC FAQ - maguire1992 - 13-10-2013 What bhp should I see after a stage 2 remap? RE: 306 FMIC FAQ - rd070707 - 13-10-2013 In and around 150 depending on other mods, arron on here rolled 154bhp there on his hd which is stage 2 mapped with a few other supporting mods. Get a good map off whippy or prosteve would be my advice RE: 306 FMIC FAQ - maguire1992 - 13-10-2013 Only mod I would say would have anything to do with bhp would be the exhaust which is just a full straight through ? RE: 306 FMIC FAQ - rd070707 - 13-10-2013 yes that is ideal. Only other thing I can think you'd need is the egr blanked off. Oh and on stage 2 the boost is usually increased slightly. Get talking to a good mapper they will sort you out RE: 306 FMIC FAQ - maguire1992 - 13-10-2013 Egr is blocked now just need it mapped out Yeah going for map tomorrow ![]() RE: 306 FMIC FAQ - rd070707 - 13-10-2013 Tomorrow? where at? please don't say torquetronix RE: 306 FMIC FAQ - mcglynn - 13-10-2013 Yeah please dont say wishart, your hdi will be running "180bhp' RE: 306 FMIC FAQ - rd070707 - 13-10-2013 Its just that the likes of prosteve has mega experience mapping 306s, the cars on here are testament to his work RE: 306 FMIC FAQ - mcglynn - 13-10-2013 Torque tronix spool some shite aswell with figures and the losses on theyre dyno aren't right either so theres 'proof' of these figures. RE: 306 FMIC FAQ - maguire1992 - 13-10-2013 Am for obd auto tune in Ballymena Wouldn't go to torque tronix RE: 306 FMIC FAQ - mcglynn - 13-10-2013 Autotune arent so bad, ive the lead here if u want to borrow it and go pro steve or whippy. Theyll map the 16hdi sensor in for u etc. RE: 306 FMIC FAQ - Arron - 13-10-2013 Seriously I would use one of the forum mappers unless your going for a live map by a diesel specialist which id imagine wouldnt be cheap. Thing ia the forum mappers specialise in thw bosch hdi fuel system so they can tailor your map I.e: launch control, rev limiters etc How much is the map from that place and what sort of gains do they think youll get RE: 306 FMIC FAQ - mcglynn - 13-10-2013 Autotune are a reputable tuner with their own in house dyno etc, but it will cost a lot more than a forum file service map RE: 306 FMIC FAQ - maguire1992 - 15-10-2013 Been to obd auto tune already and car made from 89.5 bhp to 145 bhp more than happy with it ![]() RE: 306 FMIC FAQ - rd070707 - 15-10-2013 Good job mate, does she go well? RE: 306 FMIC FAQ - mcglynn - 15-10-2013 What sort of torque figures. Standard clutch? RE: 306 FMIC FAQ - maguire1992 - 15-10-2013 Yeah goes great Can't remember he's to email me the printout RE: 306 FMIC FAQ - padge - 15-10-2013 get it mapped by someone on here, should make 155-160bhp ![]() RE: 306 FMIC FAQ - maguire1992 - 15-10-2013 219lbft of torque Will wait to the clutch would maybe slip then see about that kyle RE: 306 FMIC FAQ - mcglynn - 15-10-2013 Must go a whole lot better than before anyway! RE: 306 FMIC FAQ - Midnightclub - 16-10-2013 Sounds like it's been put on a limited torque map RE: 306 FMIC FAQ - maguire1992 - 16-10-2013 She goes really well The man said he hadn't had a 306 make 150 bhp before... |