Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
306 rallye trackday project
#61
Those mounting bells for the discs what is the thickness and offset of them, are they an off the shelf part?
Reply
Thanks given by:
#62
mounting bells are cosworth 909 parts , will try and measure offset for you this week
Reply
Thanks given by:
#63
(12-05-2015, 06:16 PM)twangy Wrote: mounting bells are cosworth 909 parts , will try and measure offset for you this week

Cheers mate. What thickness are the discs too and are they running fine with the standard GTi6 calipers, have you got any squealing issues?
Reply
Thanks given by:
#64
disc size is AP 285 x 25mm , there of the rear of 1 of my old cosworths , fit fine with calipers just had to ease caliper brackets , don't no if squeal yet as haven't used car since fitting
Reply
Thanks given by:
#65
finally back on car ,have fitted and painted rear carbon hatch ,and also carbon spoiler now fitted , also remove rub strips from side and filled holes and  painted , will flat and polish over weekend and refit replacement graphics

also painted carbon door inner on both and outer drivers  , will flat polish and fit over weekend and graphic up
Reply
Thanks given by:
#66
clear lacquered were have left bare carbon fibre
Reply
Thanks given by:
#67
Those doors look great!
This post is an artistic work of fiction and falsehood. Only a fool would take anything posted above as fact.

62k Diablo Phase 1 Gti-6:
Project Thread
Reply
Thanks given by: twangy
#68
Would you consider making making a fiberglass boot?
If so I'd be interested :-)
#2 Moonstone Blue HDI
[Image: 6b0c7309-5184-463c-9f73-2a7b96601418_zpsfdf041fe.jpg]
Reply
Thanks given by:
#69
(16-05-2015, 11:37 AM)kentiiboii Wrote: Would you consider making making a fiberglass boot?
If so I'd be interested :-)

just got to get properly on feet and will start making some panels

(16-05-2015, 08:06 AM)RetroPug Wrote: Those doors look great!

thanks mate
Reply
Thanks given by:
#70
(16-05-2015, 02:54 PM)twangy Wrote:
(16-05-2015, 11:37 AM)kentiiboii Wrote: Would you consider making making a fiberglass boot?
If so I'd be interested :-)

just got to get properly on feet and will start making some panels

(16-05-2015, 08:06 AM)RetroPug Wrote: Those doors look great!

thanks mate
Nice one :-)
#2 Moonstone Blue HDI
[Image: 6b0c7309-5184-463c-9f73-2a7b96601418_zpsfdf041fe.jpg]
Reply
Thanks given by:
#71
right then  ,flatted and polished and fitted drives side carbon door and replaced graphics , will start on other side next week  , then  wiil try and get weight on thing  
Reply
Thanks given by:
#72
carbon bonnet now painted , so just got to flat and polish and refit onto car and graphic up , has carbon showing through on some graphic like on doors . will add picture next few days
Reply
Thanks given by:
#73
Comming on really well

When are you aiming to get back rallying?
[Image: Cn91r40h.jpg] 
Astor 6 Fast road/track project
Reply
Thanks given by:
#74
(24-05-2015, 07:01 PM)7057sam Wrote: Comming on really well

When are you aiming to get back rallying?
don't know if I am going to bother rallying car for now , or just do track days and sprints for a bit till done engine mods sam ,
Reply
Thanks given by:
#75
started refitting carbon bonnet today before rain stopped play , just got to line up properly and fit bonnet pins , also got to buff front wings as need a good polish
Reply
Thanks given by:
#76
[attachment=23714]quick update , haven't really had time to do much on car with one thing and the other , but altered rear bumper , and still collecting bits for throttle bodies conversion
Reply
Thanks given by:
#77
also managed to get hold of lighter non PAS engine mounting , good weight saving as only weighs 2.7 kg compared to heavy weight standard aux bracket
Reply
Thanks given by:
#78
Sorry, what does the standard aux bracket weigh?
Reply
Thanks given by:
#79
(10-06-2015, 06:05 PM)twangy Wrote: also managed to get hold of lighter non PAS engine mounting , good weight saving as only weighs 2.7 kg compared to heavy weight standard aux bracket

where did you get the bracket from? I really need one! 
Reply
Thanks given by:
#80
(11-06-2015, 09:51 AM)Dum-Dum Wrote: Sorry, what does the standard aux bracket weigh?
standard  aux bracket weigh  over 7kg  ,
Reply
Thanks given by:
#81
(11-06-2015, 11:22 AM)Eeyore Wrote:
(10-06-2015, 06:05 PM)twangy Wrote: also managed to get hold of lighter non PAS engine mounting , good weight saving as only weighs 2.7 kg compared to heavy weight standard aux bracket

where did you get the bracket from? I really need one! 

miles , from pugracing
Reply
Thanks given by:
#82
haven't been on site for a good while due to loads of misfortune and at one stage was going to strip car and get rid of but have decided to keep and do a load more too it , so have been building new home for it , so can get stuck into it over winter

and today got roof on and remote roller shutter and car under cover


Attached Files Image(s)
       
Reply
Thanks given by:
#83
Nice! Where's the project thread for that? Tongue

Seriously though, any chance of a write up? Hoping to do something similar myself soon and would appreciate the insight.
306 HDi Deathtrap - 130bhp / 220lbft
...UPGRADING...



Reply
Thanks given by:
#84
Think of checking for asbestos before demolishing that?
Reply
Thanks given by:
#85
(22-09-2015, 06:12 PM)Paul_13 Wrote: Think of checking for asbestos before demolishing that?
had tin roof on it paul
Reply
Thanks given by:
#86
Glad to see you haven't lost heart in it and even built a new man cave for it Big Grin
[Image: 17b33c2a-8471-4313-992e-0a4b324cf926_zps2e63812a.jpg]
Team Cyril
Reply
Thanks given by:
#87
Fair do's Smile
Reply
Thanks given by:
#88
(23-09-2015, 01:47 PM)Matt-Rallye Wrote: Glad to see you haven't lost heart in it and even built a new man cave for it Big Grin

matt ,have never lost heart in car ,just had a lot of thing happen in life lately ,and was just going to sell up everything and start afresh ,but am more determine to keep car and do even more mods than I had originally planned  , man cave is essential  for winter time work  ,keeping me and car nice and dry
Reply
Thanks given by:
#89
Keep it up mate Smile
P1 XSi track car
2.4 LWB T4
Reply
Thanks given by:
#90
(24-09-2015, 07:52 PM)adam b Wrote: Keep it up mate Smile

cheers adam , hows your car coming along m8
Reply
Thanks given by:


Possibly Related Threads…
Thread Author Replies Views Last Post
  Matts £200 Cherry Rallye shell rebuild & tidy up project. Xsara goodies landed! Matt-Rallye 70 23,328 07-03-2017, 12:58 PM
Last Post: Matt-Rallye
  Matts rallye project. operation derust Matt 630 234,587 23-06-2016, 06:41 PM
Last Post: Frosty
  The toy, 306GTI trackday racer. *Dial-up warning: Picture heavy* Janne L 142 30,471 11-03-2016, 07:58 AM
Last Post: Janne L

Forum Jump:


Users browsing this thread: 3 Guest(s)