|
engine information??
|
17-05-2014, 04:45 PM
VF37CDHYE this is my chassis number minus the last 8 digits. Can anyone tell me anything about the engine i got here thanks in advance!!
 Knowing my luck its the worst ahaha
no smoke no poke... so they say!
Posts: 6,367
Threads: 87 Joined: Dec 2011 Reputation: 48 Location: South Yorks. Car Model/Spec: Rouge vallelunga 5 door Dturbo 
Thanks: 2
Given 74 thank(s) in 70 post(s)
17-05-2014, 05:00 PM
on the front of your block will be a little dirty silver plate about an inch big with a code, D8A, DHX, DHY, or something similar
Phase 1 D-Turdo, K14@24 psi, De-cat, meaty backbox, Bosch pump, grinded LDA pin, duel air fed K&N =133.7bhp & 188ft/lbs
Posts: 6,258
Threads: 371 Joined: Feb 2014 Reputation: 29 Location: suffolk Car Model/Spec: ford fiesta 
Thanks: 4
Given 82 thank(s) in 82 post(s)
17-05-2014, 05:13 PM
(This post was last modified: 17-05-2014, 05:14 PM by bashbarnard.)
Your car has a dhy in unless it has had a engine change in its life at some point.
But I have a dhy and its fine
On a break from 306oc for personal reasons. If anyone needs or wants me most of you have my number and or facebook messenger
Thanks for the good times guys n gals. I might be back. Who knows.
17-05-2014, 05:16 PM
(17-05-2014, 05:13 PM)tombarnard1989 Wrote: Your car has a dhy in unless it has had a engine change in its life at some point. yeh it did have a full engine change/belts/gearbox etc in 2008 i have recipts for it 40k ago but they dont specify any engine codes etc.. it cost the poor lad 1.4k lmao at citoren edinburgh. I am confused to what one it is now haha
no smoke no poke... so they say!
Posts: 6,258
Threads: 371 Joined: Feb 2014 Reputation: 29 Location: suffolk Car Model/Spec: ford fiesta
Thanks: 4
Given 82 thank(s) in 82 post(s)
17-05-2014, 05:21 PM
Then it will be stamped on the block for you. Ill take a look at mine kater to see where mine is printed for you. I wouodnt get caught up on it to much. They are all pretty much the same. Its said that the dhy codes had a.batch of them come out of factory with non turbo con rods in them. Causeing them to break and go through the block. Which is probally what happened to the old engine before it was replaced
On a break from 306oc for personal reasons. If anyone needs or wants me most of you have my number and or facebook messenger
Thanks for the good times guys n gals. I might be back. Who knows.
20-05-2014, 05:31 PM
sweet man that would be handy! I have tuned the pug somewhat but havnt had a chance to perfect it yet!
no smoke no poke... so they say!
22-05-2014, 09:21 AM
22-05-2014, 05:31 PM
(This post was last modified: 22-05-2014, 05:41 PM by D Turbo Lyle.)
(22-05-2014, 09:21 AM)mr_fish Wrote:(17-05-2014, 05:07 PM)D Turbo Lyle Wrote: d.8b??? [attachment=16407] thats a pic of what i seen.... is this good or bad?? lol it had an engine change 40k ago at citoren in edinburgh.. i bet it is aswell hope its not a bad thing!! haha
no smoke no poke... so they say!
|
|
« Next Oldest | Next Newest »
|
| Possibly Related Threads… | |||||
| Thread | Author | Replies | Views | Last Post | |
| Bosch VE information | bashbarnard | 0 | 863 |
11-05-2016, 09:35 PM Last Post: bashbarnard |
|
| Information about the XUD7 TE engine | 306rhys | 6 | 1,370 |
19-09-2015, 11:35 PM Last Post: Uberderv |
|
