Clutch, re using old cover
306oc - Peugeot 306 Owners Club & Forum › Engines › DW10 HDi section v
Clutch, re using old cover

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Clutch, re using old cover
Dum-Dum Offline
Lord of Unfinished Projects
Posts: 15,646
Threads: 541
Joined: Dec 2011
Reputation: 124
Location: Aylesbury
Car Model/Spec: 320bhp Impreza WRX
Thanks: 7
Given 59 thank(s) in 58 post(s)
#1
23-05-2013, 02:33 PM
I'm mega skint, if i got my hands on a paddle clutch disk would there be any issue with re using the OEM pressure plate/cover. Id get a new bearing, just looking to save money
Find
Reply
Thanks given by:
Ruan Offline
"Gearbox Side" towards engine 4 lyf

Registered users - Donated
Posts: 5,205
Threads: 91
Joined: Dec 2011
Reputation: 83
Location: Oxfordshire/Cornwall
Car Model/Spec: Moonstone DT/Volvo V50
Thanks: 2
Given 41 thank(s) in 41 post(s)
#2
23-05-2013, 07:26 PM
Be fine, long as it's not badly hotspotted.
(16-05-2016, 10:45 AM)Toms306 Wrote: Oh I don't care about the stripped threads lol, that's easily solved by hammering the bolt in. Wink
Nanstone GTD5 GT17S - XUD9TE
Volvo V50 D5 R-Design SE Sport - Daily cruise wagon.
Find
Reply
Thanks given by:
darrenjlobb Offline
Team Chronic Boost!

Registered users - Donated
Posts: 4,604
Threads: 90
Joined: Dec 2011
Reputation: 54
Location: Cornwall
Car Model/Spec: 1996 306 DT M-TDI/16
Facebook Google+ Instagram YouTube
Thanks: 0
Given 20 thank(s) in 18 post(s)
#3
23-05-2013, 07:49 PM
HDI clutch or XUD?

If XUD changing the bearing is a farce tbh, so easier to swap the lot, id personally change it, along with facing the flywheel, paddle clutchs a basturds to bed in at the best of times
| Dyno Power Runs & Steady State Facilities Available, Just Ask Anytime |
| #DervMafia |
[Image: sigi-2.png]
Website Find
Reply
Thanks given by:
Dum-Dum Offline
Lord of Unfinished Projects
Posts: 15,646
Threads: 541
Joined: Dec 2011
Reputation: 124
Location: Aylesbury
Car Model/Spec: 320bhp Impreza WRX
Thanks: 7
Given 59 thank(s) in 58 post(s)
#4
24-05-2013, 12:53 PM
HDi clutch Darren.


Ill have to take it apart and look at it. Its been in a standard HDi so shouldn't be too badly hot spotted.
Find
Reply
Thanks given by:
Toms306 Offline
wishes he'd bought a Haytch Dee Aye
Posts: 18,242
Threads: 386
Joined: Dec 2011
Reputation: 87
Location: Suffolk
Car Model/Spec: Focus Titanium
Thanks: 1
Given 118 thank(s) in 117 post(s)
#5
24-05-2013, 01:34 PM
(24-05-2013, 12:53 PM)Dum-Dum Wrote: HDi clutch Darren.


Ill have to take it apart and look at it. Its been in a standard HDi so shouldn't be too badly hot spotted.

Depends if the clutch has been slipping tbh, the one I took off ky HDi went straight in the bin as there was hot spots all over it. I had abused it for a few thousand miles though lol.

Obviously its down to money but surely it'll cost you more if you put it back together and then find you've gotta take it apart again and change it.
Find
Reply
Thanks given by:
Poodle Offline
Ruth on weekends only

Registered users - Donated
Posts: 10,864
Threads: 117
Joined: Dec 2011
Reputation: 119
Location: Southampton
Car Model/Spec: 306 HDi and friends
Thanks: 13
Given 106 thank(s) in 106 post(s)
#6
24-05-2013, 05:11 PM
Clutch hasn't been slipping.
306 HDi Deathtrap - 130bhp / 220lbft
...UPGRADING...



Find
Reply
Thanks given by:
Dum-Dum Offline
Lord of Unfinished Projects
Posts: 15,646
Threads: 541
Joined: Dec 2011
Reputation: 124
Location: Aylesbury
Car Model/Spec: 320bhp Impreza WRX
Thanks: 7
Given 59 thank(s) in 58 post(s)
#7
24-05-2013, 09:53 PM
Hasn't been slipping at all. However against my better judgement I have bought a CG clutch kit. Uprated pressure plate, un sprung paddle drive plate and a new bearing for £225 posted.
Find
Reply
Thanks given by:


Possibly Related Threads…
Thread Author Replies Views Last Post
  clutch plate, bearing, cover... different brands? Arron 1 968 31-12-2012, 10:32 AM
Last Post: Arron

Forum Jump:


Users browsing this thread: 1 Guest(s)