12-05-2012, 06:34 PM
im set on masking my head lights and i just wondered if anyone know a way of getting the grommets that holds the grill on without damaging the paint and possibly use them again. fam.
removing front grill
|
12-05-2012, 06:34 PM
im set on masking my head lights and i just wondered if anyone know a way of getting the grommets that holds the grill on without damaging the paint and possibly use them again. fam.
12-05-2012, 06:36 PM
You should be able to get a screw driver under the centre part of them and lift it up. You can then pull them out nicely.
Team Eaton
1999 China Blue 306 GTi6 - Eaton Supercharged - 214.5bhp 181lbft
12-05-2012, 06:39 PM
tryed this but didnt want to force it. last time i made a right cock up of em. will give it another go.
12-05-2012, 06:43 PM
kingy Wrote:tryed this but didnt want to force it. last time i made a right cock up of em. will give it another go. Tbh once they have been in for a while, they don't like to come out without breaking. There only about 30p from pug so might be worth buying some then breaking the old ones out.
Team Eaton
1999 China Blue 306 GTi6 - Eaton Supercharged - 214.5bhp 181lbft
12-05-2012, 06:49 PM
Either that or use a trim tool, it's like a forked flat blade. Goes under the centre plug, either side of the stem to prise the plug up.
Hope that made at least some sense lol Member of the 99% warning or you're nothing club 2000 Moonstone 1.8 Meridian - Sold 2000 China 3dr XS - Dead 1998 Diablo 3dr XSI
12-05-2012, 06:50 PM
Umm you can get your fingers underneath the surrounding grill area and pull upwards this will remove those pesky pegs.
Captain Standard
12-05-2012, 06:52 PM
Been here long enough king atkeast get it in the right section lol but yeah as said get a screwdriver in the middle of the "peg"
12-05-2012, 06:59 PM
4WayDiablo Wrote:Been here long enough king atkeast get it in the right section lol but yeah as said get a screwdriver in the middle of the "peg"your right mate. my bad. thick as shite mate lol. think im gonna leave it now anyways, as long as its done for fcs.
12-05-2012, 07:50 PM
Get a kitchen fork, that's what I used. Was bloody brilliant didn't damage anything
TEAM CONROD SHITTING RALLYE!
12-05-2012, 09:04 PM
Not read through this fully but I find that wd40 and a kitchen fork you would use to eat your dinner does the trick
12-05-2012, 09:06 PM
mark_airey Wrote:Not read through this fully but I find that wd40 and a kitchen fork you would use to eat your dinner does the trickIdeally a fork you're hoping to use for dinner that evening! Those work best. Also works well if you're facing an Easterly direction, with odd socks on.
12-05-2012, 09:08 PM
Scott Wrote:mark_airey Wrote:Not read through this fully but I find that wd40 and a kitchen fork you would use to eat your dinner does the trickIdeally a fork you're hoping to use for dinner that evening! Those work best. Also works well if you're facing an Easterly direction, with odd socks on. FYC scott, if you get the 4 pronged variety the gap between the prongs is almost exactly the same as the pin that splits the clip and fits nicely between the top and bottom section of the clip, I was actually being serious for a change
12-05-2012, 09:14 PM
fork, or lever them up enough to use a claw hammer (use a bit of old rag to protect the paint) If you snap them, then buy new ones and drill the feckers out!
Welding and fabrication projects undertaken, contact me for more information.
12-05-2012, 09:16 PM
Jonny81191 Wrote:fork, or lever them up enough to use a claw hammer (use a bit of old rag to protect the paint) If you snap them, then buy new ones and drill the feckers out! there is no wonder you always break stuff also why drill them out? a small nail will push the pin right out of the other side and then you can just lift the bottom section out if it comes to that
12-05-2012, 09:23 PM
I don't always break stuff! I had to drill some out cos the top came off whilst I was attempting to remove them.
Welding and fabrication projects undertaken, contact me for more information.
12-05-2012, 09:27 PM
Jonny81191 Wrote:I don't always break stuff! I had to drill some out cos the top came off whilst I was attempting to remove them.Have to admit your getting quite good at it though as I said, if that is the problem and you pull the top off you can just push the center pin right through the clip mucho's less pissing around kingy Wrote:will this do If that is what you use to eat your dinner then press on
12-05-2012, 09:29 PM
drive into that, that'll get your grill off. (won't guarantee the refitting bit though) Welding and fabrication projects undertaken, contact me for more information.
12-05-2012, 09:31 PM
@ jonny
kingy Wrote:mark you dum ass, i ment the clips. I know, and as my first reply said "using a kitchen fork like you would use to eat dinner" so as I say, if you use one of those to eat dinner then carry on |
« Next Oldest | Next Newest »
|
Possibly Related Threads… | |||||
Thread | Author | Replies | Views | Last Post | |
Front plastic grill | Hdi and proud of it | 2 | 1,107 |
28-09-2014, 07:36 PM Last Post: Hdi and proud of it |
|
front bumper grill removal | karl1989 | 6 | 2,109 |
02-12-2012, 08:25 PM Last Post: karl1989 |
|
Removing grill and hockey sticks | aaron_one | 3 | 1,571 |
24-11-2012, 10:38 AM Last Post: aaron_one |