Posts: 7,347
Threads: 163
Joined: Dec 2011
Reputation:
53
Location: Leeds
Car Model/Spec: 406 HDI
Thanks: 0
Given 18 thank(s) in 15 post(s)
The drive down the side of my house is in a bad way. It has a concrete base, and at some point in the past had tarmac laid over that, which seems to have dried out completely to the point where it's covered in loose aggregate and patches of the concrete below are showing through. There's also a few soft spots caused by oil/fuel contamination. Been meaning to sort it for the 4 years I've lived here but never got round to it, but now I'm planning a garage it needs sorting. The one lad I've had out to quote has said it needs jack hammering down to the dirt level and fully replacing at the cost of £2200 which I just can't afford, but I do see his point and it is pretty bad, so I have 2 questions really...
1. How much could I do it for DIY? It's about 30 metres long by 4 metres wide, so what would you budget for jack hammer rental, shuttering, concrete, hardcore and anything else I need? I've laid concrete before pretty successfully but never over such a large area.
2. Is there any way of repairing/skimming over what's already there?
Cheers
Posts: 5,847
Threads: 169
Joined: Dec 2011
Reputation:
91
Location: South London
Car Model/Spec: 2003 Jaguar S-Type Sport 3.0V6
Thanks: 1
Given 1 thank(s) in 1 post(s)
I don't know what prices are like up where you are but for down here would be as follows;
1- 15 cubic meters of 20mm ballast (based on a 150mm lay to wearing course to cover 120m sq. at £42.50 a meter delivered -£850
2- Cement to go with the above; based on 6 bags a cubic meter - £382.5
3- Re-bar to go into concrete to avoid expansion and cracking - 4 sheets @£27.5 a sheet £110
4- Wood for shuttering - £~£80
£1422
Plus and tools hire you may need, waste clearance, e.g. skips or grab hire.
.
Are you sure it is 120m sq? That is an awfully large area to concrete.
Member of the 99% warning or you're nothing club
2000 Moonstone 1.8 Meridian - Sold
2000 China 3dr XS - Dead
1998 Diablo 3dr XSI
Posts: 7,347
Threads: 163
Joined: Dec 2011
Reputation:
53
Location: Leeds
Car Model/Spec: 406 HDI
Thanks: 0
Given 18 thank(s) in 15 post(s)
Yep, it's a full length driveway running from the street to my back fence, and it's a pretty big back garden. It's an absolute shit tip, has been since I've lived here, knee deep in brambles and weeds with gravel underneath, my lass had lived here by herself for a long time and wasn't any good at gardening, and it got so bad it was just ignored while we sorted out the inside, but now that's done it's time for new decking, a nice lawn, built in BBQ, garage and new shed, gonna be a huge project though...
Well at those prices you've given me £2200 doesn't sound that bad, that's including a 24x12 hardstanding at the end as well, might just have to suck it up and pay for it.
Posts: 5,847
Threads: 169
Joined: Dec 2011
Reputation:
91
Location: South London
Car Model/Spec: 2003 Jaguar S-Type Sport 3.0V6
Thanks: 1
Given 1 thank(s) in 1 post(s)
08-02-2014, 06:29 PM
(This post was last modified: 08-02-2014, 06:30 PM by Grant.)
Fair enough then.
Just make sure, if you do get somebody to do it, you specify that you want expansions joints and wire in it. Otherwise it will crack up and be a mess in a few years. Even sooner if you are on soft ground.
If you dig it out, and want to provide me with a copious (and I mean copious :p ) amount of coffee and bacon, we can get it concreted in a weekend.
That said, it would probably be just as cost effective for you to pay to have it done after tool hire and waste disposal etc.. Offer's there though x
Member of the 99% warning or you're nothing club
2000 Moonstone 1.8 Meridian - Sold
2000 China 3dr XS - Dead
1998 Diablo 3dr XSI
Posts: 8,749
Threads: 208
Joined: Jan 2012
Reputation:
60
Location: Wiltshire
Car Model/Spec: ph2 Gti6 / ph4 HDI Estate
Thanks: 1
Given 5 thank(s) in 5 post(s)
Yeeaahh bit ott grant, @ 150mm deep i think Rebar is needed not for the weight of cars a low speed , ( with a good)
Plus with your calculations you have missed the price of scalps to base up with plus the rental of a good size wacker plate
Member of 99% warning or your nothing club!
Posts: 7,347
Threads: 163
Joined: Dec 2011
Reputation:
53
Location: Leeds
Car Model/Spec: 406 HDI
Thanks: 0
Given 18 thank(s) in 15 post(s)
Ha, thanks mate. My plan was to use the remnants of the drive as hardcore to level the hardstanding for the garage, so I doubt there'd be any waste disposal at all, if anything I'd have to bring in hardcore I reckon! I'd provide more than coffee and bacon, I'd include a warm bed, curry and shitloads of ale!
I might still try save the original surface. Biggest concern is the huge soft spot where the shitty Lucas pump on the DT was leaking when I got it
Posts: 8,749
Threads: 208
Joined: Jan 2012
Reputation:
60
Location: Wiltshire
Car Model/Spec: ph2 Gti6 / ph4 HDI Estate
Thanks: 1
Given 5 thank(s) in 5 post(s)
08-02-2014, 08:31 PM
(This post was last modified: 08-02-2014, 08:42 PM by puglove.)
& i make that 18m cubed grant
Member of 99% warning or your nothing club!
Posts: 15,646
Threads: 541
Joined: Dec 2011
Reputation:
124
Location: Aylesbury
Car Model/Spec: 320bhp Impreza WRX
Thanks: 7
Given 59 thank(s) in 58 post(s)
Id measure up what depth the concrete currently is and if the concrete is good then scrape the tarmac off. Also I wouldn't be buying sand and cement, Just get ready mix poured in off the truck.
Posts: 8,749
Threads: 208
Joined: Jan 2012
Reputation:
60
Location: Wiltshire
Car Model/Spec: ph2 Gti6 / ph4 HDI Estate
Thanks: 1
Given 5 thank(s) in 5 post(s)
You would really need to brake the hardcore up small, to get a decent base , large bits of hard core tends to move and leave voids meaning very premature failure of the concrete, i see this alot
Concreting is like 30% of my job btw im not just guessing lol
Member of 99% warning or your nothing club!
Posts: 3,342
Threads: 151
Joined: Dec 2011
Reputation:
14
Location: Rotherham
Car Model/Spec: 306 D-turbo
Thanks: 1
Given 0 thank(s) in 0 post(s)
Bacon ale and curry, I'm there!
£2200 does sound a good price but if you can do it yourself under £1500 I know what I would be doing
I know f*ck all about concrete apart from you pour it and it sets hard
But I'm willing to come over and lend a hand
Team Doesn't own a 306
Posts: 8,749
Threads: 208
Joined: Jan 2012
Reputation:
60
Location: Wiltshire
Car Model/Spec: ph2 Gti6 / ph4 HDI Estate
Thanks: 1
Given 5 thank(s) in 5 post(s)
Right i just txt my dad (manger at a concrete plant) @ £72 per meter delivered for 18m = £1296 on concrete alone so £2200 is a fecking good deal to be fair
Member of 99% warning or your nothing club!
Posts: 7,347
Threads: 163
Joined: Dec 2011
Reputation:
53
Location: Leeds
Car Model/Spec: 406 HDI
Thanks: 0
Given 18 thank(s) in 15 post(s)
(08-02-2014, 08:33 PM)Dum-Dum Wrote: Id measure up what depth the concrete currently is and if the concrete is good then scrape the tarmac off. Also I wouldn't be buying sand and cement, Just get ready mix poured in off the truck.
Any tips on scraping off the crete? I have a feeling it's in usable condition under the tar...
(08-02-2014, 08:34 PM)puglove Wrote: You would really need to brake the hardcore up small, to get a decent base , large bits of hard core tends to move and leave voids meaning very premature failure of the concrete, i see this alot
Concreting is like 30% of my job btw im not just guessing lol
Nice one mate. I'm pretty good at hitting shit with hammers
(08-02-2014, 08:39 PM)Danny2009 Wrote: Bacon ale and curry, I'm there!
£2200 does sound a good price but if you can do it yourself under £1500 I know what I would be doing
I know f*ck all about concrete apart from you pour it and it sets hard
But I'm willing to come over and lend a hand
Thanks mate
(08-02-2014, 08:46 PM)puglove Wrote: Right i just txt my dad (manger at a concrete plant) @ £72 per meter delivered for 18m = £1296 on concrete alone so £2200 is a fecking good deal to be fair
I didn't think it sounded bad actually. I reckon I'll go with that if I can't scrape the tar off.
Posts: 2,105
Threads: 170
Joined: Dec 2011
Reputation:
5
Location: west yorkshire
Car Model/Spec: xud 1.9 dturbo
Thanks: 2
Given 0 thank(s) in 0 post(s)
Wasn't a gypsy was he Liam lol
Venetian XUD ph2 heaven
Ph3 perv cab heaven
Black ph1 XUD died
Moonstone hdi stage 2
Posts: 15,646
Threads: 541
Joined: Dec 2011
Reputation:
124
Location: Aylesbury
Car Model/Spec: 320bhp Impreza WRX
Thanks: 7
Given 59 thank(s) in 58 post(s)
For scraping the tar off just just cover it in WVO daily for a week and you'll probably just be able to scoop it up.
Posts: 1,417
Threads: 34
Joined: Dec 2011
Reputation:
8
Thanks: 0
Given 8 thank(s) in 8 post(s)
(08-02-2014, 10:51 PM)Dum-Dum Wrote: For scraping the tar off just just cover it in WVO daily for a week and you'll probably just be able to scoop it up.
I can't see him wasting veg oil! He's a northerner haha
Posts: 7,347
Threads: 163
Joined: Dec 2011
Reputation:
53
Location: Leeds
Car Model/Spec: 406 HDI
Thanks: 0
Given 18 thank(s) in 15 post(s)
(08-02-2014, 10:49 PM)karl1989 Wrote: Wasn't a gypsy was he Liam lol
No he's a mate of my dads, I know to stay away from those thieving f*ckers
(08-02-2014, 10:51 PM)Dum-Dum Wrote: For scraping the tar off just just cover it in WVO daily for a week and you'll probably just be able to scoop it up.
Would that work? I know diesel will work, theres a big soft patch where the DT was leaking diesel on it before I did the Bosch swap and found a huge crack in the back of the pump...
(08-02-2014, 10:56 PM)Seb_Ryan Wrote: (08-02-2014, 10:51 PM)Dum-Dum Wrote: For scraping the tar off just just cover it in WVO daily for a week and you'll probably just be able to scoop it up.
I can't see him wasting veg oil! He's a northerner haha
I'll have an unlimited supply free soon
Posts: 5,847
Threads: 169
Joined: Dec 2011
Reputation:
91
Location: South London
Car Model/Spec: 2003 Jaguar S-Type Sport 3.0V6
Thanks: 1
Given 1 thank(s) in 1 post(s)
(08-02-2014, 08:27 PM)puglove Wrote: Yeeaahh bit ott grant, @ 150mm deep i think Rebar is needed not for the weight of cars a low speed , ( with a good)
Plus with your calculations you have missed the price of scalps to base up with plus the rental of a good size wacker plate
Dude, you been drinking? That makes very little sense
I see little/no point in putting type1 underneath 6 inches of concrete. What are you aiming to achieve with that?
The rebar would be for bridging the expansion joints, to allow the right amount of movement in the concrete when it settles, without cracking.
You may work with concrete, but I have letters after my name in this shit (hard to believe I know :p )
Member of the 99% warning or you're nothing club
2000 Moonstone 1.8 Meridian - Sold
2000 China 3dr XS - Dead
1998 Diablo 3dr XSI
Posts: 7,347
Threads: 163
Joined: Dec 2011
Reputation:
53
Location: Leeds
Car Model/Spec: 406 HDI
Thanks: 0
Given 18 thank(s) in 15 post(s)
Ok, so here's what I've got. I know it's awful but it was the last priority, central heating, new bathroom, new kitchen, patio doors and redecoration all had to come first!
Algae on the surface, and you can see how dry and brittle it is.
Soft spot from diesel contamination. That's a footprint!
Sunken drain cover.
Broken patches showing decent looking concrete underneath.
The existing fence that a car cant get past, this will be stripped and reconfigured.
Posts: 7,347
Threads: 163
Joined: Dec 2011
Reputation:
53
Location: Leeds
Car Model/Spec: 406 HDI
Thanks: 0
Given 18 thank(s) in 15 post(s)
Down the back.
Looks pretty solid.
Garden has crept over the tarmac but where I've scraped it back its sokid and smooth.
What do we reckon, can it be saved?
Posts: 511
Threads: 7
Joined: Aug 2013
Reputation:
2
Location: Scotland!
Car Model/Spec: 106 slo-nad
Thanks: 24
Given 7 thank(s) in 7 post(s)
Just lift the tarmac, looks like there's sod all wrong with the conrete
A moments silence please, for our brothers in the NAD-zone.
Posts: 7,347
Threads: 163
Joined: Dec 2011
Reputation:
53
Location: Leeds
Car Model/Spec: 406 HDI
Thanks: 0
Given 18 thank(s) in 15 post(s)
(09-02-2014, 11:44 AM)Martin306 Wrote: Just lift the tarmac, looks like there's sod all wrong with the conrete
What's the best way to do that? I thought that, where the concrete shows through it's really solid and crack-free, I can't understand why it's had shitty pikey-grade tarmac shoved on top!
Posts: 5,847
Threads: 169
Joined: Dec 2011
Reputation:
91
Location: South London
Car Model/Spec: 2003 Jaguar S-Type Sport 3.0V6
Thanks: 1
Given 1 thank(s) in 1 post(s)
Probably because a gippo has done exactly that. Tarmacced the drive by putting a skin over the top, that your driveway is testament to the fact, is shit and doesn't work.
Member of the 99% warning or you're nothing club
2000 Moonstone 1.8 Meridian - Sold
2000 China 3dr XS - Dead
1998 Diablo 3dr XSI
Posts: 7,347
Threads: 163
Joined: Dec 2011
Reputation:
53
Location: Leeds
Car Model/Spec: 406 HDI
Thanks: 0
Given 18 thank(s) in 15 post(s)
(09-02-2014, 12:07 PM)Grant Wrote: Probably because a gippo has done exactly that. Tarmacced the drive by putting a skin over the top, that your driveway is testament to the fact, is shit and doesn't work.
I just can't understand why, the concrete seems fine. It's just a waste.
Posts: 511
Threads: 7
Joined: Aug 2013
Reputation:
2
Location: Scotland!
Car Model/Spec: 106 slo-nad
Thanks: 24
Given 7 thank(s) in 7 post(s)
I'm no tarmac expert but that cheap stuff can be very hard to lift. The local council used to use that on back paths near me.
A moments silence please, for our brothers in the NAD-zone.
Posts: 15,646
Threads: 541
Joined: Dec 2011
Reputation:
124
Location: Aylesbury
Car Model/Spec: 320bhp Impreza WRX
Thanks: 7
Given 59 thank(s) in 58 post(s)
Liam veg lifts tarmac just as well as diesel. The road outside my old house started coming up with the veg that was leaking/spilled on it.
Posts: 5,847
Threads: 169
Joined: Dec 2011
Reputation:
91
Location: South London
Car Model/Spec: 2003 Jaguar S-Type Sport 3.0V6
Thanks: 1
Given 1 thank(s) in 1 post(s)
(09-02-2014, 12:19 PM)THE_Liam Wrote: (09-02-2014, 12:07 PM)Grant Wrote: Probably because a gippo has done exactly that. Tarmacced the drive by putting a skin over the top, that your driveway is testament to the fact, is shit and doesn't work.
I just can't understand why, the concrete seems fine. It's just a waste.
Down here, a lot of the 'doorstep traders' are very pushy. You never know, the previous owner/tenant could have been bullied into having it done.
They will then just put the smalls amount of tarmac over the greatest area to charge hideous prices.
Member of the 99% warning or you're nothing club
2000 Moonstone 1.8 Meridian - Sold
2000 China 3dr XS - Dead
1998 Diablo 3dr XSI
Posts: 7,347
Threads: 163
Joined: Dec 2011
Reputation:
53
Location: Leeds
Car Model/Spec: 406 HDI
Thanks: 0
Given 18 thank(s) in 15 post(s)
(09-02-2014, 04:07 PM)Grant Wrote: (09-02-2014, 12:19 PM)THE_Liam Wrote: (09-02-2014, 12:07 PM)Grant Wrote: Probably because a gippo has done exactly that. Tarmacced the drive by putting a skin over the top, that your driveway is testament to the fact, is shit and doesn't work.
I just can't understand why, the concrete seems fine. It's just a waste.
Down here, a lot of the 'doorstep traders' are very pushy. You never know, the previous owner/tenant could have been bullied into having it done.
They will then just put the smalls amount of tarmac over the greatest area to charge hideous prices.
Yeah we get that here as well. I had one trying to tell me I could be sued if someone tripped on my driveway, and if I didn't let him resurface it he'd arrange for someone to fall on it and contact a solicitor. I ended up chasing him down the street, don't threaten me on my own property you lady garden.
Posts: 594
Threads: 25
Joined: Dec 2011
Reputation:
3
Location: Leeds
Car Model/Spec: Vectra & Berlingo
Thanks: 5
Given 5 thank(s) in 5 post(s)
My old man had his concrete drive skimmed over with resin and stones. Looks like pebbledash but hard wearing.
If I where you I'd get some 3x2 flags from reclamation yard and pave it. Or broken flags for crazy paving.
Posts: 3,342
Threads: 151
Joined: Dec 2011
Reputation:
14
Location: Rotherham
Car Model/Spec: 306 D-turbo
Thanks: 1
Given 0 thank(s) in 0 post(s)
Paving slabs are shite broke countless jacking up on them
Team Doesn't own a 306
|