Cutting boost holes!!
306oc - Peugeot 306 Owners Club & Forum › Engines › XUD Section v
Cutting boost holes!!

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Cutting boost holes!!
silverzx Offline
Always leaves skidz

Registered users - Donated
Posts: 4,926
Threads: 266
Joined: Dec 2011
Reputation: 18
Location: Somerset
Car Model/Spec: 205 DTurbo
Thanks: 73
Given 7 thank(s) in 7 post(s)
#1
07-05-2013, 11:20 PM
Anyone able to recommend a drill bit / piece / thing for cutting 3" holes in my chassis nice and easily for boost pipes to run through? Don't really fancy cutting squares and covering with spare rubber window/door seals!
Supercharged GTi6 Build
S14 Zenki Build
[Image: signature.png]
Find
Reply
Thanks given by:
samass Offline
Colin McSamass

Registered users - Donated
Posts: 7,152
Threads: 130
Joined: Jan 2012
Reputation: 82
Location: Kingston
Car Model/Spec: 106 GO-NAD
Thanks: 0
Given 0 thank(s) in 0 post(s)
#2
07-05-2013, 11:37 PM
Holes saw.
[Image: k6f9Fk]


Member of the 99% warning or you're nothing club
Find
Reply
Thanks given by:
silverzx Offline
Always leaves skidz

Registered users - Donated
Posts: 4,926
Threads: 266
Joined: Dec 2011
Reputation: 18
Location: Somerset
Car Model/Spec: 205 DTurbo
Thanks: 73
Given 7 thank(s) in 7 post(s)
#3
07-05-2013, 11:45 PM
(07-05-2013, 11:37 PM)samass Wrote: Holes saw.

Thats the name then! I can look myself now I know what there called. Wink
Supercharged GTi6 Build
S14 Zenki Build
[Image: signature.png]
Find
Reply
Thanks given by:
samass Offline
Colin McSamass

Registered users - Donated
Posts: 7,152
Threads: 130
Joined: Jan 2012
Reputation: 82
Location: Kingston
Car Model/Spec: 106 GO-NAD
Thanks: 0
Given 0 thank(s) in 0 post(s)
#4
07-05-2013, 11:58 PM
But without the extra s
[Image: k6f9Fk]


Member of the 99% warning or you're nothing club
Find
Reply
Thanks given by:
darrenjlobb Offline
Team Chronic Boost!

Registered users - Donated
Posts: 4,604
Threads: 90
Joined: Dec 2011
Reputation: 54
Location: Cornwall
Car Model/Spec: 1996 306 DT M-TDI/16
Facebook Google+ Instagram YouTube
Thanks: 0
Given 20 thank(s) in 18 post(s)
#5
10-05-2013, 09:29 AM (This post was last modified: 10-05-2013, 09:30 AM by darrenjlobb.)
plasma cutter / hole saw / jigsaw if your feeling rash....
note, on mine i slid a silicon up over the hose where it went through to stop any knocking / protect it a bit.
| Dyno Power Runs & Steady State Facilities Available, Just Ask Anytime |
| #DervMafia |
[Image: sigi-2.png]
Website Find
Reply
Thanks given by:
silverzx Offline
Always leaves skidz

Registered users - Donated
Posts: 4,926
Threads: 266
Joined: Dec 2011
Reputation: 18
Location: Somerset
Car Model/Spec: 205 DTurbo
Thanks: 73
Given 7 thank(s) in 7 post(s)
#6
10-05-2013, 11:17 PM
(10-05-2013, 09:29 AM)darrenjlobb Wrote: plasma cutter / hole saw / jigsaw if your feeling rash....
note, on mine i slid a silicon up over the hose where it went through to stop any knocking / protect it a bit.

Ordered a set of cheapy hole saws with sizes from quater inch up to 2 and a half inches I think.

I'll give them a go before anything! Smile
Supercharged GTi6 Build
S14 Zenki Build
[Image: signature.png]
Find
Reply
Thanks given by:
ozonehostile Offline
Turning into a 306

Registered users - Donated
Posts: 5,946
Threads: 141
Joined: Oct 2012
Reputation: 35
Location: Herefordshire
Car Model/Spec: 106 rallye, GTi6, Hdi dturbo
Thanks: 3
Given 14 thank(s) in 14 post(s)
#7
10-05-2013, 11:32 PM
hole saw then jig saw to make the hole bigger. file off the edges then as darren says, piece of hose in the hole to stop rattles/damage to pipe Smile
Current stable
'09 Mercedes E320cdi wagon 
'99 306 gti6
Find
Reply
Thanks given by:


Possibly Related Threads…
Thread Author Replies Views Last Post
  Flywheel has two timing holes? Fozzy 14 5,763 28-08-2012, 10:09 PM
Last Post: CJ_Derv

Forum Jump:


Users browsing this thread: 1 Guest(s)