K03 MBC

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
K03 MBC
#1
Has anyone got any pics of a MBC fitted to a K03? I understand how they fit on a GT15 but can't quite work out where it would go on the K03.

Any help appreciated
[Image: Ty8kl7b.jpg]
Reply
Thanks given by:
#2
no expenses spared...

[Image: A5mpp.png]
Diablo Hdi Dturbo and 205 1.9 project - it lives!
Reply
Thanks given by:
#3
haha cheers for that ginge.. it's not quite the same on a K03 though, think the boost take off to the actuator is done through a banjo bolt
[Image: Ty8kl7b.jpg]
Reply
Thanks given by:
#4
you got any pictures to where you have access to ??
Diablo Hdi Dturbo and 205 1.9 project - it lives!
Reply
Thanks given by:
#5
Nothing useful i'm afraid.. but i know there's naff all room. Hopefully someone who's already done it can pop along with a decent pic Big Grin
[Image: Ty8kl7b.jpg]
Reply
Thanks given by:
#6
Cut the metal pipe in two, then jubilee clip some hose around the 2 bits of metal pipe.
(16-05-2016, 10:45 AM)Toms306 Wrote: Oh I don't care about the stripped threads lol, that's easily solved by hammering the bolt in. Wink
Nanstone GTD5 GT17S - XUD9TE
Volvo V50 D5 R-Design SE Sport - Daily cruise wagon.
Reply
Thanks given by:
#7
ginge191 Wrote:no expenses spared...

[Image: A5mpp.png]
that MBC is actually the wrong way round..

just sayin'
Reply
Thanks given by:
#8
What he said ^^ Flip it so boost is pushing spring not how it is Smile
| Dyno Power Runs & Steady State Facilities Available, Just Ask Anytime |
| #DervMafia |

[Image: sigi-2.png]
Reply
Thanks given by:
#9
Cheers guys, What should i use to cut the pipe? Thinking about it won't it squash the pipe then give me effectively de-wastegate?
[Image: Ty8kl7b.jpg]
Reply
Thanks given by:
#10
Just cut it with penknife or something, its only a tiny rubber hose....

Better still remove it at both ends and run two longer new hoses up to somewhere easier to adjust!
| Dyno Power Runs & Steady State Facilities Available, Just Ask Anytime |
| #DervMafia |

[Image: sigi-2.png]
Reply
Thanks given by:
#11
Ah ok, ruan said it was a metal pipe? I've already got some hosing which i should be able to use, I'll take a load of pics when i do it for anyone else wondering
[Image: Ty8kl7b.jpg]
Reply
Thanks given by:
#12
If it's got a banjo bolt I assume it's a metal pipe?

I know the K14 uses a metal pipe, K03 might not - either way, just shove it someway between the two?
(16-05-2016, 10:45 AM)Toms306 Wrote: Oh I don't care about the stripped threads lol, that's easily solved by hammering the bolt in. Wink
Nanstone GTD5 GT17S - XUD9TE
Volvo V50 D5 R-Design SE Sport - Daily cruise wagon.
Reply
Thanks given by:
#13
Okay mate, it was difficult to see so not sure if it's a metal or rubber pipe, I'll see if i can get some decent pictures then that should tell me
[Image: Ty8kl7b.jpg]
Reply
Thanks given by:
#14
rubber pipe will be black and bendy, metal pipe will be metallic looking and not bendy Tongue
Team Orange Engine Bay

My flickr photostream - http://www.flickr.com/photos/markairey
Reply
Thanks given by:
#15
mark_airey Wrote:rubber pipe will be black and bendy, metal pipe will be metallic looking and not bendy Tongue

Unless it's all oily because i had a boost leak... in which case.. everythings black Tongue
[Image: Ty8kl7b.jpg]
Reply
Thanks given by:
#16
Midnightclub Wrote:Unless it's all oily because i had a boost leak... in which case.. everythings black Tongue

The bendy rule still applies though Big Grin
Team Orange Engine Bay

My flickr photostream - http://www.flickr.com/photos/markairey
Reply
Thanks given by:
#17
I could do with pictures of this too.
Welding and fabrication projects undertaken, contact me for more information.

Reply
Thanks given by:
#18
I'll be setting one of these up on a K14 soon. How easy is the pipe to access from underneath? Also what is the diameter, if anyone knows. Thanks.
Reply
Thanks given by:
#19
Jonny81191 Wrote:I could do with pictures of this too.

No you couldn't, man up Tongue
Team Orange Engine Bay

My flickr photostream - http://www.flickr.com/photos/markairey
Reply
Thanks given by:
#20
for the GT15, i just cut the pipe half way roughly, then pushed 2 fual line connector barbs in, then a few feet of blue silicone pipe up to near the top mount.

oh and i think its 5mm internal diameter, as the 6mm barbs i used were tight as f*ck..
Reply
Thanks given by:
#21
mark_airey Wrote:
Jonny81191 Wrote:I could do with pictures of this too.

No you couldn't, man up Tongue


get round to mine of an evening and help then!
Welding and fabrication projects undertaken, contact me for more information.

Reply
Thanks given by:


Forum Jump:


Users browsing this thread: 2 Guest(s)