Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
cylinder head xud11 12 s
#3
Big Grin 
(05-01-2016, 04:20 PM)bashbarnard Wrote: I think I get the jist here. You're running a 2.1 with an 8v head. Trying to gain more power. The 2.1 head flows more and a td04 will NOT suit the engine. To laggy. These make all there power down low. Get a decent turbo on there. Piggy had some good power figures have a read through his thread.

 td04l the 13t - and not bad but lack of a diet high CVs

I have an exhaust casing of 6 cm if I put in a 5 cm its 'll Sufis to reduce lag

I have seen post Peggy has a turbo gt2056 I croi but difficult to achieve 230 hp

then I pensse the head 8s is an obstacle to good performance of the 12 s will be better now

I made a little video of the counter but not in the right format I have is watching piggy video on you tube and I m comes out rather well Blush
Reply
Thanks given by:


Messages In This Thread
cylinder head xud11 12 s - by niciou - 05-01-2016, 04:02 PM
RE: cylinder head xud11 12 s - by bashbarnard - 05-01-2016, 04:20 PM
RE: cylinder head xud11 12 s - by niciou - 05-01-2016, 04:28 PM
RE: cylinder head xud11 12 s - by niciou - 05-01-2016, 05:13 PM
RE: cylinder head xud11 12 s - by Mattcheese31 - 05-01-2016, 05:43 PM
RE: cylinder head xud11 12 s - by niciou - 05-01-2016, 05:48 PM
RE: cylinder head xud11 12 s - by Piggy - 05-01-2016, 05:48 PM
RE: cylinder head xud11 12 s - by niciou - 05-01-2016, 05:55 PM
RE: cylinder head xud11 12 s - by Piggy - 05-01-2016, 06:12 PM
RE: cylinder head xud11 12 s - by niciou - 05-01-2016, 06:28 PM
RE: cylinder head xud11 12 s - by Piggy - 05-01-2016, 06:56 PM
RE: cylinder head xud11 12 s - by niciou - 05-01-2016, 07:04 PM
RE: cylinder head xud11 12 s - by niciou - 06-01-2016, 06:04 PM
RE: cylinder head xud11 12 s - by Mattcheese31 - 06-01-2016, 07:08 PM
RE: cylinder head xud11 12 s - by niciou - 06-01-2016, 07:26 PM
RE: cylinder head xud11 12 s - by Ruan - 08-01-2016, 01:40 AM
RE: cylinder head xud11 12 s - by niciou - 08-01-2016, 02:01 PM
RE: cylinder head xud11 12 s - by Mattcheese31 - 08-01-2016, 09:09 AM

Possibly Related Threads…
Thread Author Replies Views Last Post
  Cylinder head manni surface sanding 306Puggy 9 3,569 05-08-2020, 03:11 PM
Last Post: ekjdm14
  lower height pistons xud11 of 1 mm niciou 3 5,462 01-03-2018, 07:44 PM
Last Post: niciou
  How To - 2.1TD Swap / XUD11 Fitting Dum-Dum 101 103,026 28-07-2017, 12:18 PM
Last Post: rachaeljf

Forum Jump:


Users browsing this thread: 1 Guest(s)