Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Show me some dyno print outs
#39
(03-07-2013, 10:23 AM)ste91 Wrote: And another league again for common rail injection I expect?

Don't get me wrong here I'm impressed with this 180bhp L series, it's a big step forward in progress as most are stuck with the standard turbo and we finally have some proven results from a bolt on hybrid turbo, I think you guys were stuck at a similar point with XUD's before, and then suddenly everyone's coming out with big turbos/etc...?

I'm keeping an eye on the MG/R forum from the guy who's running this 180bhp L series to see how it fares with long term reliability as all previous attempts at hybrid turbos just gave head lift/HGF issues and not really that much of a power gain, I think the highest was something like 170bhp but it didn't last very long. However that was basically a standard GT15 with a bigger comp wheel - bad recipe for EMP, whereas this hybrid uses a much bigger turbine housing.

Tuned XUD's seem to be pretty strong apart from the occasional thrown rod?

Yeah, common rail gives you all the benifits of DI, and the added benifit of such extreme injection pressure, and such PRECISE timing of injection, the control you have over common rail is just insane compared to mech injection, hence much cleaner results can be had, and alot more power can be made...

Hybrid turbos are good in theory, but personally id rather find a turbo from another suitable vehicle (bigger diesel) and make the complete unit fit, for many reasons, one, because its cheaper, two because if it pops, you can just get another off the shelf the same, and 3 because I just dont like hybrids in general!

The only real issues with the XUD when your tuning them to around 200hp are conrods and head studs, both of which can be resolved, but will cost you. That said, sometimes rods seem to be fine at higher power, just depends on the state of tune / luck at the best of times tbh.... Ive never seen in the bottom end of one of those L series motors, what are the rods in them like?
| Dyno Power Runs & Steady State Facilities Available, Just Ask Anytime |
| #DervMafia |

[Image: sigi-2.png]
Reply
Thanks given by:


Messages In This Thread
Show me some dyno print outs - by ste91 - 27-06-2013, 07:38 PM
RE: Show me some dyno print outs - by 4WayDiablo - 27-06-2013, 07:59 PM
RE: Show me some dyno print outs - by cwspellowe - 27-06-2013, 08:11 PM
RE: Show me some dyno print outs - by Danny2009 - 27-06-2013, 08:05 PM
RE: Show me some dyno print outs - by Jenkosowls - 27-06-2013, 09:39 PM
RE: Show me some dyno print outs - by ste91 - 27-06-2013, 08:08 PM
RE: Show me some dyno print outs - by ste91 - 27-06-2013, 08:18 PM
RE: Show me some dyno print outs - by Anton - 27-06-2013, 08:21 PM
RE: Show me some dyno print outs - by cwspellowe - 27-06-2013, 08:25 PM
RE: Show me some dyno print outs - by ste91 - 27-06-2013, 08:29 PM
RE: Show me some dyno print outs - by Piggy - 27-06-2013, 08:31 PM
RE: Show me some dyno print outs - by ste91 - 27-06-2013, 08:39 PM
RE: Show me some dyno print outs - by darrenjlobb - 27-06-2013, 08:41 PM
RE: Show me some dyno print outs - by Anton - 27-06-2013, 08:43 PM
RE: Show me some dyno print outs - by Piggy - 27-06-2013, 08:43 PM
RE: Show me some dyno print outs - by Tom - 27-06-2013, 09:15 PM
RE: Show me some dyno print outs - by ste91 - 27-06-2013, 09:20 PM
RE: Show me some dyno print outs - by Jenkosowls - 27-06-2013, 10:12 PM
RE: Show me some dyno print outs - by darrenjlobb - 27-06-2013, 10:15 PM
RE: Show me some dyno print outs - by Ruan - 02-07-2013, 08:53 PM
RE: Show me some dyno print outs - by darrenjlobb - 03-07-2013, 09:35 AM
RE: Show me some dyno print outs - by ste91 - 28-06-2013, 08:41 PM
RE: Show me some dyno print outs - by Ruan - 29-06-2013, 09:04 AM
RE: Show me some dyno print outs - by ste91 - 29-06-2013, 10:17 AM
RE: Show me some dyno print outs - by Ruan - 29-06-2013, 11:58 AM
RE: Show me some dyno print outs - by ste91 - 29-06-2013, 12:24 PM
RE: Show me some dyno print outs - by Ruan - 02-07-2013, 09:00 PM
RE: Show me some dyno print outs - by ste91 - 03-07-2013, 09:38 AM
RE: Show me some dyno print outs - by Danny2009 - 02-07-2013, 09:23 PM
RE: Show me some dyno print outs - by Anton - 02-07-2013, 09:24 PM
RE: Show me some dyno print outs - by darrenjlobb - 03-07-2013, 09:41 AM
RE: Show me some dyno print outs - by ste91 - 03-07-2013, 10:23 AM
RE: Show me some dyno print outs - by darrenjlobb - 03-07-2013, 12:03 PM
RE: Show me some dyno print outs - by ste91 - 03-07-2013, 12:28 PM
RE: Show me some dyno print outs - by Anton - 03-07-2013, 10:35 AM
RE: Show me some dyno print outs - by ste91 - 03-07-2013, 11:05 AM
RE: Show me some dyno print outs - by Dum-Dum - 03-07-2013, 10:36 AM
RE: Show me some dyno print outs - by karl1989 - 03-07-2013, 01:44 PM

Forum Jump:


Users browsing this thread: 1 Guest(s)