removing front grill

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
removing front grill
#1
im set on masking my head lights and i just wondered if anyone know a way of getting the grommets that holds the grill on without damaging the paint and possibly use them again. fam.
[Image: newsig_zpsee86fa10.jpg]
Reply
Thanks given by:
#2
You should be able to get a screw driver under the centre part of them and lift it up. You can then pull them out nicely.
Team Eaton


1999 China Blue 306 GTi6 - Eaton Supercharged - 214.5bhp 181lbft
Reply
Thanks given by:
#3
tryed this but didnt want to force it. last time i made a right cock up of em. will give it another go.
[Image: newsig_zpsee86fa10.jpg]
Reply
Thanks given by:
#4
kingy Wrote:tryed this but didnt want to force it. last time i made a right cock up of em. will give it another go.


Tbh once they have been in for a while, they don't like to come out without breaking. There only about 30p from pug so might be worth buying some then breaking the old ones out.
Team Eaton


1999 China Blue 306 GTi6 - Eaton Supercharged - 214.5bhp 181lbft
Reply
Thanks given by:
#5
Either that or use a trim tool, it's like a forked flat blade. Goes under the centre plug, either side of the stem to prise the plug up.


Hope that made at least some sense lol
[Image: car-1.jpg]

Member of the 99% warning or you're nothing club


2000 Moonstone 1.8 Meridian - Sold
2000 China 3dr XS - Dead
1998 Diablo 3dr XSI
Reply
Thanks given by:
#6
Umm you can get your fingers underneath the surrounding grill area and pull upwards this will remove those pesky pegs.
Captain Standard

Reply
Thanks given by:
#7
Been here long enough king atkeast get it in the right section lol but yeah as said get a screwdriver in the middle of the "peg"
[Image: IMG_20130925_181339_zps95df48fa.jpg]
Reply
Thanks given by:
#8
i wanted it done tomorrow and it pug parts aint open.
[Image: newsig_zpsee86fa10.jpg]
Reply
Thanks given by:
#9
4WayDiablo Wrote:Been here long enough king atkeast get it in the right section lol but yeah as said get a screwdriver in the middle of the "peg"
your right mate. my bad. thick as shite mate lol.

think im gonna leave it now anyways, as long as its done for fcs.
[Image: newsig_zpsee86fa10.jpg]
Reply
Thanks given by:
#10
Get a kitchen fork, that's what I used. Was bloody brilliant didn't damage anything
[Image: 20A1806D-891D-40FB-BD52-AD519177A607-734...391753.jpg]
TEAM CONROD SHITTING RALLYE!
Reply
Thanks given by:
#11
mint. will give that ago. cheers.
[Image: newsig_zpsee86fa10.jpg]
Reply
Thanks given by:
#12
Not read through this fully but I find that wd40 and a kitchen fork you would use to eat your dinner does the trick Wink
Team Orange Engine Bay

My flickr photostream - http://www.flickr.com/photos/markairey
Reply
Thanks given by:
#13
mark_airey Wrote:Not read through this fully but I find that wd40 and a kitchen fork you would use to eat your dinner does the trick Wink
Ideally a fork you're hoping to use for dinner that evening! Those work best. Also works well if you're facing an Easterly direction, with odd socks on.
Reply
Thanks given by:
#14
Scott Wrote:
mark_airey Wrote:Not read through this fully but I find that wd40 and a kitchen fork you would use to eat your dinner does the trick Wink
Ideally a fork you're hoping to use for dinner that evening! Those work best. Also works well if you're facing an Easterly direction, with odd socks on.

FYC scott, if you get the 4 pronged variety the gap between the prongs is almost exactly the same as the pin that splits the clip and fits nicely between the top and bottom section of the clip, I was actually being serious for a change Tongue
Team Orange Engine Bay

My flickr photostream - http://www.flickr.com/photos/markairey
Reply
Thanks given by:
#15
fork, or lever them up enough to use a claw hammer (use a bit of old rag to protect the paint) If you snap them, then buy new ones and drill the feckers out!
Welding and fabrication projects undertaken, contact me for more information.

Reply
Thanks given by:
#16
Jonny81191 Wrote:fork, or lever them up enough to use a claw hammer (use a bit of old rag to protect the paint) If you snap them, then buy new ones and drill the feckers out!

there is no wonder you always break stuff lmao also why drill them out? a small nail will push the pin right out of the other side and then you can just lift the bottom section out if it comes to that Wink
Team Orange Engine Bay

My flickr photostream - http://www.flickr.com/photos/markairey
Reply
Thanks given by:
#17
I don't always break stuff! I had to drill some out cos the top came off whilst I was attempting to remove them.
Welding and fabrication projects undertaken, contact me for more information.

Reply
Thanks given by:
#18
will this do

[Image: Digging-Fork.jpg]
[Image: newsig_zpsee86fa10.jpg]
Reply
Thanks given by:
#19
Jonny81191 Wrote:I don't always break stuff! I had to drill some out cos the top came off whilst I was attempting to remove them.
Have to admit your getting quite good at it though Tongue as I said, if that is the problem and you pull the top off you can just push the center pin right through the clip Wink mucho's less pissing around Big Grin

kingy Wrote:will this do

[Image: Digging-Fork.jpg]

If that is what you use to eat your dinner then press on lmao
Team Orange Engine Bay

My flickr photostream - http://www.flickr.com/photos/markairey
Reply
Thanks given by:
#20
mark you dum ass, i ment the clips.
[Image: newsig_zpsee86fa10.jpg]
Reply
Thanks given by:
#21
[Image: Fork-in-the-Road.jpg]

drive into that, that'll get your grill off. (won't guarantee the refitting bit though)
Welding and fabrication projects undertaken, contact me for more information.

Reply
Thanks given by:
#22
lmao
[Image: newsig_zpsee86fa10.jpg]
Reply
Thanks given by:
#23
lmao @ jonny

kingy Wrote:mark you dum ass, i ment the clips.

I know, and as my first reply said "using a kitchen fork like you would use to eat dinner" so as I say, if you use one of those to eat dinner then carry on Tongue
Team Orange Engine Bay

My flickr photostream - http://www.flickr.com/photos/markairey
Reply
Thanks given by:
#24
i got ya, just loling marra. Wink
[Image: newsig_zpsee86fa10.jpg]
Reply
Thanks given by:


Possibly Related Threads…
Thread Author Replies Views Last Post
  Front plastic grill Hdi and proud of it 2 1,110 28-09-2014, 07:36 PM
Last Post: Hdi and proud of it
  front bumper grill removal karl1989 6 2,119 02-12-2012, 08:25 PM
Last Post: karl1989
  Removing grill and hockey sticks aaron_one 3 1,577 24-11-2012, 10:38 AM
Last Post: aaron_one

Forum Jump:


Users browsing this thread: 1 Guest(s)