Posts: 6,569
Threads: 183
Joined: Dec 2011
Reputation:
20
Location: eastwood/notts
Car Model/Spec: moonstone hdi #2
Thanks: 0
Given 8 thank(s) in 8 post(s)
25-09-2014, 01:16 PM
(This post was last modified: 25-09-2014, 01:18 PM by kentiiboii.)
QUICK REPLY NEEDED PLEASE!!!
Just come to fit my rippthrough lower brace, but I have a power steering pipe that runs under the engine in the way. If I give it a bit of force I can just get it on, will that be ok?
Here we go.
#2 Moonstone Blue HDI
![[Image: 6b0c7309-5184-463c-9f73-2a7b96601418_zpsfdf041fe.jpg]](http://i512.photobucket.com/albums/t326/kent16_2008/6b0c7309-5184-463c-9f73-2a7b96601418_zpsfdf041fe.jpg)
Posts: 6,569
Threads: 183
Joined: Dec 2011
Reputation:
20
Location: eastwood/notts
Car Model/Spec: moonstone hdi #2
Thanks: 0
Given 8 thank(s) in 8 post(s)
Sorted it, someone had bolted the pipe wrong way round before hand.
#2 Moonstone Blue HDI
Posts: 2,490
Threads: 164
Joined: Jun 2012
Reputation:
25
Location: Honiton
Car Model/Spec: Gti6
Thanks: 0
Given 4 thank(s) in 4 post(s)
Yeah that pipe was a bit low on mine and rattled on the brace until I adjusted where it sat
Posts: 6,569
Threads: 183
Joined: Dec 2011
Reputation:
20
Location: eastwood/notts
Car Model/Spec: moonstone hdi #2
Thanks: 0
Given 8 thank(s) in 8 post(s)
Yeah once I noticed where it was wrong the brace went on fine.
Didn't think it should of been that low.
#2 Moonstone Blue HDI
Posts: 1,950
Threads: 55
Joined: Dec 2011
Reputation:
17
Location: Rotherham
Car Model/Spec: 406 V6
Thanks: 3
Given 10 thank(s) in 10 post(s)
Those sometimes get bolted on too low even when they're up in the right place - there's quite a lot of slop on the bolt holes, so it's worth checking it's as far up as it'll go before fitting a brace anyway
Custom roll cages/shiny suspension bits/general fabrication work undertaken, PM me.
Top engine mount repair/reinforcement/chocking for cracked chassis and high powered cars, drive in, drive out, 2 hour turnaround.
Posts: 15,646
Threads: 541
Joined: Dec 2011
Reputation:
124
Location: Aylesbury
Car Model/Spec: 320bhp Impreza WRX
Thanks: 7
Given 59 thank(s) in 58 post(s)
You still making these Phil?
Posts: 1,950
Threads: 55
Joined: Dec 2011
Reputation:
17
Location: Rotherham
Car Model/Spec: 406 V6
Thanks: 3
Given 10 thank(s) in 10 post(s)
I will be when I get chance - I've got some steel bent up ready, just need to weld up some ends and chop and weld the lot together, things are a bit hectic atm, lost my nan about 6 weeks back and my grandad's in a bit of a mess, so I'm on babysitting duty/suicide watch at the minute, which is taking up most of my spare time.
Custom roll cages/shiny suspension bits/general fabrication work undertaken, PM me.
Top engine mount repair/reinforcement/chocking for cracked chassis and high powered cars, drive in, drive out, 2 hour turnaround.
Posts: 1,950
Threads: 55
Joined: Dec 2011
Reputation:
17
Location: Rotherham
Car Model/Spec: 406 V6
Thanks: 3
Given 10 thank(s) in 10 post(s)
I saw it, and the other one
I've got enough for 10-12 braces but am busy with the buggy and some other work for the next week or two, I'll see if I can knock some up the weekend after next.
Custom roll cages/shiny suspension bits/general fabrication work undertaken, PM me.
Top engine mount repair/reinforcement/chocking for cracked chassis and high powered cars, drive in, drive out, 2 hour turnaround.
![[Image: sig2_zps5d67efb7.jpg]](http://i1133.photobucket.com/albums/m598/rocker8742/sig2_zps5d67efb7.jpg)
