smooth boot

[sam]

How easy is it to smooth a boot? And is it best to get to get it welded were the boot lock/pop used to be?

[DazzaHDI]

Make sure its a ph3 boot mate otherwise youll get a massive rust bubble under the rubber seal like mine has :/

[sam]

Mine is a phase 3 chap but ill keep that in mind chap

[kingy]

Im looking into this.
Deffo get it welded. Much better.
My problem is the popper and how to wire it in.
I can remember dum doing a guide for this but he just used bubbly gum to fill his hole. But hey if it works then it works.

[Piggy]

just need a centrol locking servo motor, earth it, and then run a positive feed to it from a switch inside.

[kentiiboii]

Im looking into this.
Deffo get it welded. Much better.
My problem is the popper and how to wire it in.
I can remember dum doing a guide for this but he just used bubbly gum to fill his hole. But hey if it works then it works.

One sat at mine with popper just needs painting.

[kingy]

Im looking into this.
Deffo get it welded. Much better.
My problem is the popper and how to wire it in.
I can remember dum doing a guide for this but he just used bubbly gum to fill his hole. But hey if it works then it works.

One sat at mine with popper just needs painting.

Ill have it mate. 100%. How much?

[DazzaHDI]

Im looking into this.
Deffo get it welded. Much better.
My problem is the popper and how to wire it in.
I can remember dum doing a guide for this but he just used bubbly gum to fill his hole. But hey if it works then it works.

One sat at mine with popper just needs painting.

I was going to have that off you? You didn't reply to my question about collection?

[Grant]

I did a guide a while ago. It wasnt welded, but it never budged and inch.

clicky

[C.A.R.]

Mine was welded, I can't take credit for it, but I did wire up the popper, much easier than you'd expect, probably took less than an hour and that included running a signal wire from the boot hatch, down the C-pillar and to the control panel on the drivers side of the car. Hook it up to permanent live though, or you have to f*ck about turning the ignition on to open your boot.

[kentiiboii]

Im looking into this.
Deffo get it welded. Much better.
My problem is the popper and how to wire it in.
I can remember dum doing a guide for this but he just used bubbly gum to fill his hole. But hey if it works then it works.

One sat at mine with popper just needs painting.

Ill have it mate. 100%. How much?

Pmd

Im looking into this.
Deffo get it welded. Much better.
My problem is the popper and how to wire it in.
I can remember dum doing a guide for this but he just used bubbly gum to fill his hole. But hey if it works then it works.

One sat at mine with popper just needs painting.

I was going to have that off you? You didn't reply to my question about collection?

Sorry mate just checked my pms back till last year havnt seen anything but sorry

[DazzaHDI]

One sat at mine with popper just needs painting.

Ill have it mate. 100%. How much?

Pmd

One sat at mine with popper just needs painting.

I was going to have that off you? You didn't reply to my question about collection?

Sorry mate just checked my pms back till last year havnt seen anything but sorry

YHPM

http://306oc.co.uk/forum/thread-15083.html

[306newbie]

you could also just use some fiberglass from behind to hold a metal plate in place then a little skim of filler on the outside

[Piggy]

you could also just use some fiberglass from behind to hold a metal plate in place then a little skim of filler on the outside

can't see the benefit of fibreglassing a piece of metal in to only fill/skim over when you may aswell just fill over the fibreglass!?

[Eeyore]

there is a guide. just put the popper on the rear wiper wiring. best and easiest way really!