Recharging a cone air filter

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Recharging a cone air filter
#1
Hi I bought an aftermarket cone air filter, I have left it in a bowl of boiling water with a dissolved dishwasher tablet and bloody hell the waters black !!!! I will recleanse it with just boiling hot water and leave it to dry.

The question is what can I use on the filter to recharge it so dust particles stick to the it, should I buy a k&n recharge kit or is there anything better or just as good that wont cost the earth??
[Image: siggy1.jpg]

the smokey old bus that sounds like a tractor...
Reply
Thanks given by:
#2
id use wd40, or some other light spray oil, just gunna do the same thing
[Image: k6f9Fk]


Member of the 99% warning or you're nothing club
Reply
Thanks given by:
#3
as I told you devils....a spray grease of some sort.
Wishes for more power...
Reply
Thanks given by:
#4
(18-09-2013, 08:27 PM)Piggy Wrote: as I told you devils....a spray grease of some sort.

It was the word "grease" i instantly thought way too thick and thought about wd40 but I've never recharged a filter before so thought I'd ask before fudging it up lol

(18-09-2013, 08:27 PM)samass Wrote: id use wd40, or some other light spray oil, just gunna do the same thing

Ha ha that's a lot cheaper than a recharge kit lol
[Image: siggy1.jpg]

the smokey old bus that sounds like a tractor...
Reply
Thanks given by:
#5
Id just plug it in overnight did you not get a charger with it? Can buy one with different voltages and ends from Argos
TD04 11mm Sedan, now 2.1 vnt

Sedan Project http://306oc.co.uk/forum/thread-5763.html

Provence Dturbo Dead
Blaze 1.6 Dead
China 5dr '6 Death by cambelt failure
Matt White HDI estate Death by wiring
Sedan Dturbo aka triggers broom
Diablo estate Dturbo Living dead
Reply
Thanks given by:
#6
(18-09-2013, 09:01 PM)HDIkyle Wrote: Id just plug it in overnight did you not get a charger with it? Can buy one with different voltages and ends from Argos

.....??? lol
[Image: siggy1.jpg]

the smokey old bus that sounds like a tractor...
Reply
Thanks given by:
#7
this is what i used to use...run out now, as I got a can when i left me old garage. shame...cracking stuff.

http://www.innotecworld.com/products/gre...oductid=88
Wishes for more power...
Reply
Thanks given by:
#8
Xud? Defilter it...
/end of thread
[Image: IMG_20130925_181339_zps95df48fa.jpg]
Reply
Thanks given by:
#9
Defilter? Pussy! Go deturbo!
[Image: mcetg0.png]

ZR VVC Homebrew mapping project: http://306oc.co.uk/forum/showthread.php?tid=14360
Reply
Thanks given by:
#10
wd40 evaperates off so is no good as it wont retain the dust once gone
id go with 3-in-1 spray oil for a cheap option
on 4 or two stoke stuff we used to oil the filters with the two stroke oil that we mixed in the tank
but the propper filter oil is not that expensive
Reply
Thanks given by:
#11
(19-09-2013, 07:47 AM)cully Wrote: wd40 evaperates off so is no good as it wont retain the dust once gone
id go with 3-in-1 spray oil for a cheap option
on 4 or two stoke stuff we used to oil the filters with the two stroke oil that we mixed in the tank
but the propper filter oil is not that expensive

So actual oil then, just thin viscosity?
[Image: siggy1.jpg]

the smokey old bus that sounds like a tractor...
Reply
Thanks given by:
#12
yeah I realised I bee saying GREASE all this time...my bad... Doh

I mean a spray oil of some sort!
Wishes for more power...
Reply
Thanks given by:
#13
(19-09-2013, 09:56 AM)devils_fuel Wrote: So actual oil then, just thin viscosity?

yes but it has got to stay wet and not dry out
as the idea is to catch the particles by sticking to the oil

oh and hdis dont like oil in there MAF sensor as it coats the sensor giving false/slow reacting readings
Reply
Thanks given by:
#14
(19-09-2013, 10:11 AM)cully Wrote:
(19-09-2013, 09:56 AM)devils_fuel Wrote: So actual oil then, just thin viscosity?

yes but it has got to stay wet and not dry out
as the idea is to catch the particles by sticking to the oil

oh and hdis dont like oil in there MAF sensor as it coats the sensor giving false/slow reacting readings

Good job I have a crappy DT lol

Anyone recommend me a good filter recharge kit?
[Image: siggy1.jpg]

the smokey old bus that sounds like a tractor...
Reply
Thanks given by:
#15
ive always used 2 stroke only as ive had some laying around from my bike days
00' 106 Indy - Moonstone - Sold
97' 106 XT 1.6 - Mayerling Green - Swapped
95' 306 P1 DT - Onyx - Scrapped
97' 306 P2 DT - Silver - Scrapped
97' 306 P2 DT - Onyx - SORN awaiting scrap
Reply
Thanks given by:
#16
Am i the only one reading this thinking ffs if its small enough to get through your filter the xud really isnt going to mind?
Doesnt even own a 306.
Reply
Thanks given by:
#17
(19-09-2013, 10:55 AM)Tom Wrote: Am i the only one reading this thinking ffs if its small enough to get through your filter the xud really isnt going to mind?

But the oil stops it getting through as it sticks to it...I can't be bothered really but I best do it, with my luck it would kill my car without it lol
[Image: siggy1.jpg]

the smokey old bus that sounds like a tractor...
Reply
Thanks given by:
#18
Well thats fair enough lol
Doesnt even own a 306.
Reply
Thanks given by:
#19
(19-09-2013, 10:54 AM)adamm306 Wrote: ive always used 2 stroke only as ive had some laying around from my bike days

I'm a noob at servicing cone filters, so do you paint the oil on or..?
[Image: siggy1.jpg]

the smokey old bus that sounds like a tractor...
Reply
Thanks given by:
#20
Defiltered FTW!
[Image: av5ym8.jpg]
Reply
Thanks given by:
#21
foam air filters used to be soaked in ordinary engine oil before fitting....................................??

when was completing my apprenticeship (moons ago), in the early 80's original vw beetles still coming into dealership for servicing used oil bath type air filters........
Reply
Thanks given by:
#22
Gonna revive this thread rather than starting a new one. The cone filter i have is filthy, but i don't have any dishwasher tablets to dissolve in a bucket of water, so does anyone have any better suggestions?
[Image: P1060836_zpsz3xgxt7q.jpg]
Reply
Thanks given by:
#23
buy a recharge kit . . /thread . .Smile
Phase 1 D-Turdo, K14@24 psi, De-cat, meaty backbox, Bosch pump, grinded LDA pin, duel air fed K&N =133.7bhp & 188ft/lbs
Reply
Thanks given by:
#24
Yeah, good call.....except i'm skint and tight. Pretty much looking for some kind of free solution to this. Tongue
[Image: P1060836_zpsz3xgxt7q.jpg]
Reply
Thanks given by:
#25
cheep enough . . . .last for ages . .

http://www.ebay.co.uk/itm/K-N-Filter-99-...1c371e083d
Phase 1 D-Turdo, K14@24 psi, De-cat, meaty backbox, Bosch pump, grinded LDA pin, duel air fed K&N =133.7bhp & 188ft/lbs
Reply
Thanks given by:
#26
Fella, I cleaned my filter in a bowl with a. Dishwasher tab in and then rinsed 4 times

Then I painted engine oil on to the filter with a paintbrush and all is well

Cost me £2 in total and the filter is like new Smile
[Image: siggy1.jpg]

the smokey old bus that sounds like a tractor...
Reply
Thanks given by:
#27
How long did you soak the filter in the bowl with the tablet? Managed to find one, and the filter is now in the bowl.
[Image: P1060836_zpsz3xgxt7q.jpg]
Reply
Thanks given by:
#28
(19-09-2013, 08:57 PM)Jimbo Wrote: Defiltered FTW!
(18-09-2013, 09:25 PM)4WayDiablo Wrote: Xud? Defilter it...
/end of thread

defilter it they said it would be fun they said hole blown in the turbo they never said Sad Tongue
00' 106 Indy - Moonstone - Sold
97' 106 XT 1.6 - Mayerling Green - Swapped
95' 306 P1 DT - Onyx - Scrapped
97' 306 P2 DT - Silver - Scrapped
97' 306 P2 DT - Onyx - SORN awaiting scrap
Reply
Thanks given by:
#29
Defiltered is FTW tbh, but i will be reinstating the original pipework again over the winter months, same as i did last year. Hence im now cleaning the cone filter. Tongue

If you kill the turbo because its defiltered, it just makes for a good excuse to put a bigger turbo on! lol
[Image: P1060836_zpsz3xgxt7q.jpg]
Reply
Thanks given by:
#30
it was FTW till it sucked something in and killed my turbo lol
00' 106 Indy - Moonstone - Sold
97' 106 XT 1.6 - Mayerling Green - Swapped
95' 306 P1 DT - Onyx - Scrapped
97' 306 P2 DT - Silver - Scrapped
97' 306 P2 DT - Onyx - SORN awaiting scrap
Reply
Thanks given by:


Possibly Related Threads…
Thread Author Replies Views Last Post
  Cone filter Willo 30 7,960 27-11-2012, 04:22 PM
Last Post: CJ_Derv

Forum Jump:


Users browsing this thread: 2 Guest(s)