Hub nut size?
306oc - Peugeot 306 Owners Club & Forum › Engines › XUD Section v
Hub nut size?

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Hub nut size?
silverzx Offline
Always leaves skidz

Registered users - Donated
Posts: 4,926
Threads: 266
Joined: Dec 2011
Reputation: 18
Location: Somerset
Car Model/Spec: 205 DTurbo
Thanks: 73
Given 7 thank(s) in 7 post(s)
#1
01-02-2013, 09:43 AM
Can anyone tell me the size of the nut in the centre of the hub as I'm trying to get drive shaft out of the gearbox for removal.

Biggest I had has 32mm so I'm guessing it's 34/36?
Supercharged GTi6 Build
S14 Zenki Build
[Image: signature.png]
Find
Reply
Thanks given by:
aggyj17 Offline
Starting to Live for the 306
Posts: 866
Threads: 61
Joined: Dec 2011
Reputation: 4
Thanks: 0
Given 6 thank(s) in 5 post(s)
#2
01-02-2013, 09:51 AM
35mm but a 36mm will fit Big Grin
Find
Reply
Thanks given by:
Mattcheese31 Offline
Part of a Bumming Club
Moderators
Posts: 6,367
Threads: 87
Joined: Dec 2011
Reputation: 48
Location: South Yorks.
Car Model/Spec: Rouge vallelunga 5 door Dturbo
Soundcloud YouTube
Thanks: 2
Given 74 thank(s) in 70 post(s)
#3
01-02-2013, 11:22 AM
35mm mate . .Smile
Phase 1 D-Turdo, K14@24 psi, De-cat, meaty backbox, Bosch pump, grinded LDA pin, duel air fed K&N =133.7bhp & 188ft/lbs
Find
Reply
Thanks given by:
Tom Offline
Living for the 205

Registered users - Donated
Posts: 6,482
Threads: 226
Joined: Dec 2011
Reputation: 24
Location: Cornwall
Car Model/Spec: A3 TDi
Thanks: 0
Given 0 thank(s) in 0 post(s)
#4
01-02-2013, 02:08 PM
I couldnt even find a 35 in halfords last time! Ended up buy a 36 for 12 f*cking quid!
Doesnt even own a 306.
Find
Reply
Thanks given by:
Oil-burner Offline
Living for the 306

Registered users - Donated
Posts: 1,847
Threads: 56
Joined: Feb 2012
Reputation: 19
Location: Chesterfield
Car Model/Spec: Moonstone HDi
Thanks: 0
Given 0 thank(s) in 0 post(s)
#5
01-02-2013, 02:48 PM
(01-02-2013, 02:08 PM)Tom Wrote: I couldnt even find a 35 in halfords last time! Ended up buy a 36 for 12 f*cking quid!

I did the same. They are a total bitch to crack I welded the socket onto a 3ft bar.
Doesn't feck about now!
[Image: A1A3B2B1-9269-463A-9F21-2ABF4CE9BEAC-165...A3B3F7.jpg]
Find
Reply
Thanks given by:
silverzx Offline
Always leaves skidz

Registered users - Donated
Posts: 4,926
Threads: 266
Joined: Dec 2011
Reputation: 18
Location: Somerset
Car Model/Spec: 205 DTurbo
Thanks: 73
Given 7 thank(s) in 7 post(s)
#6
01-02-2013, 05:48 PM
Cheers guys!
Supercharged GTi6 Build
S14 Zenki Build
[Image: signature.png]
Find
Reply
Thanks given by:
Jtrigga Offline
Active Member
Posts: 701
Threads: 59
Joined: Dec 2011
Reputation: 3
Location: Gillingham Kent
Car Model/Spec: 306 D-turbo
Thanks: 0
Given 0 thank(s) in 0 post(s)
#7
01-02-2013, 07:44 PM
Or use a blow torch just be careful of melting brake lines and boots
Bye Bye D-Turbo
Phase 1 GTi-6 now has a new owner
Rolling in the: Phase 3 HDI Wagon

The current estate project: http://306oc.co.uk/forum/thread-22237.html
Find
Reply
Thanks given by:
Tom Offline
Living for the 205

Registered users - Donated
Posts: 6,482
Threads: 226
Joined: Dec 2011
Reputation: 24
Location: Cornwall
Car Model/Spec: A3 TDi
Thanks: 0
Given 0 thank(s) in 0 post(s)
#8
01-02-2013, 08:54 PM
(01-02-2013, 02:48 PM)Oil-burner Wrote:
(01-02-2013, 02:08 PM)Tom Wrote: I couldnt even find a 35 in halfords last time! Ended up buy a 36 for 12 f*cking quid!

I did the same. They are a total bitch to crack I welded the socket onto a 3ft bar.
Doesn't feck about now!

I wouldnt even attempt one without a bar! Having someone stand on the brakes tends to help Smile
Doesnt even own a 306.
Find
Reply
Thanks given by:
swampy Offline
Starting to Live for the 306
Posts: 1,072
Threads: 57
Joined: May 2012
Reputation: 3
Location: Peterborough
Car Model/Spec: 306 s16 406 v6 Saab 93 Ttid
Thanks: 1
Given 3 thank(s) in 3 post(s)
#9
01-02-2013, 09:00 PM
If you have centre less wheels remove the centre cap and slacken the nut with the wheels on the floor
Find
Reply
Thanks given by:
Tom Offline
Living for the 205

Registered users - Donated
Posts: 6,482
Threads: 226
Joined: Dec 2011
Reputation: 24
Location: Cornwall
Car Model/Spec: A3 TDi
Thanks: 0
Given 0 thank(s) in 0 post(s)
#10
01-02-2013, 09:02 PM
(01-02-2013, 09:00 PM)swampy Wrote: If you have centre less wheels remove the centre cap and slacken the nut with the wheels on the floor

That is a damn good shout!
Doesnt even own a 306.
Find
Reply
Thanks given by:
HDIkyle Offline
BX hoarder
Posts: 1,766
Threads: 252
Joined: Dec 2011
Reputation: 7
Location: Sheffield/Leeds
Car Model/Spec: Xud sedan/Xud estate
Thanks: 2
Given 2 thank(s) in 2 post(s)
#11
02-02-2013, 12:18 AM
They are bloody tight just keep bouncing on the bar it will go eventually. I find afew bounces stood on it works fine. Done several this way
TD04 11mm Sedan, now 2.1 vnt

Sedan Project http://306oc.co.uk/forum/thread-5763.html

Provence Dturbo Dead
Blaze 1.6 Dead
China 5dr '6 Death by cambelt failure
Matt White HDI estate Death by wiring
Sedan Dturbo aka triggers broom
Diablo estate Dturbo Living dead
Find
Reply
Thanks given by:
kentiiboii Offline
Turning into a 306
Posts: 6,569
Threads: 183
Joined: Dec 2011
Reputation: 20
Location: eastwood/notts
Car Model/Spec: moonstone hdi #2
Thanks: 0
Given 8 thank(s) in 8 post(s)
#12
02-02-2013, 12:42 AM (This post was last modified: 02-02-2013, 12:43 AM by kentiiboii.)
We ended up taking whole hub out. Was much easier!
(02-02-2013, 12:42 AM)kentiiboii Wrote: We ended up taking whole hub out. Was much easier!

Just to add to that.... At the time I was 23stone bouncing up and down on mine still didn't budge.
#2 Moonstone Blue HDI
[Image: 6b0c7309-5184-463c-9f73-2a7b96601418_zpsfdf041fe.jpg]
Find
Reply
Thanks given by:
ash240970 Offline
Involved with ATM

Registered users - Donated
Posts: 1,776
Threads: 82
Joined: Jan 2012
Reputation: 14
Location: Droitwich, Worcestershire
Car Model/Spec: P0XY Ph2 Dtub 5dr
Thanks: 0
Given 0 thank(s) in 0 post(s)
#13
02-02-2013, 12:46 AM
(02-02-2013, 12:18 AM)HDIkyle Wrote: They are bloody tight just keep bouncing on the bar it will go eventually. I find afew bounces stood on it works fine. Done several this way

Spike and I bent a bar like this so resorted to bouncing on my torque wrench - which I promptly broke Sad
Find
Reply
Thanks given by:
silverzx Offline
Always leaves skidz

Registered users - Donated
Posts: 4,926
Threads: 266
Joined: Dec 2011
Reputation: 18
Location: Somerset
Car Model/Spec: 205 DTurbo
Thanks: 73
Given 7 thank(s) in 7 post(s)
#14
02-02-2013, 06:42 PM
Thanks for the vote of confidence fella's. Tongue
Supercharged GTi6 Build
S14 Zenki Build
[Image: signature.png]
Find
Reply
Thanks given by:
Tom Offline
Living for the 205

Registered users - Donated
Posts: 6,482
Threads: 226
Joined: Dec 2011
Reputation: 24
Location: Cornwall
Car Model/Spec: A3 TDi
Thanks: 0
Given 0 thank(s) in 0 post(s)
#15
02-02-2013, 06:50 PM
Either you lot have found some seriously tight ones or all the ones i've done have been easy... Or im hench as f*ck? lolz

But being serious i just lean over and pul the bar up towards me and never had an issue :/
Doesnt even own a 306.
Find
Reply
Thanks given by:
silverzx Offline
Always leaves skidz

Registered users - Donated
Posts: 4,926
Threads: 266
Joined: Dec 2011
Reputation: 18
Location: Somerset
Car Model/Spec: 205 DTurbo
Thanks: 73
Given 7 thank(s) in 7 post(s)
#16
03-02-2013, 07:21 PM
My 35mm just slips too much, probably shouldn't have got an impact one.

What's the alternative? Whole Hub off? Trying to get the gearbox out.
Supercharged GTi6 Build
S14 Zenki Build
[Image: signature.png]
Find
Reply
Thanks given by:


Possibly Related Threads…
Thread Author Replies Views Last Post
  Top mount intercooler bolt size/ timing hole size LewisG306 2 1,795 13-07-2014, 10:44 AM
Last Post: LewisG306

Forum Jump:


Users browsing this thread: 1 Guest(s)