Posts: 1,804
Threads: 129
Joined: Mar 2012
Reputation:
11
Thanks: 0
Given 0 thank(s) in 0 post(s)
I started tidying up the garage when I got home from work today after watching Darrens latest video's it made me think of how much of a state mine is. But I ended up stripping down my old engine and making even more of a mess.
Started by removing the head to find the headgasket to be the wrong one by the looks of it. The water channels from the block to head looked very restricted by the gasket with holes about 3mm round...
Apart from that the bores, valves and pistons looked in surprisingly good nick for a 176k engine.
Then removed the sump and started taking everything out. I've got to the point where I just need to remove the bottom pulley to take the crank out but everythings unbolted apart from that which is annoying as the pulley bolts f-ing tight!
Half tempted to rebuild it and fit the HDI rods I bought of Dave and maybe some ARP studs. Either that or get another '9 and fit them to that.
I would upload the pick but I havnt got the iphone cable  sorry
Stage 2 XUD Sedan
Posts: 1,064
Threads: 29
Joined: May 2012
Reputation:
18
Location: Portsmouth
Car Model/Spec: mx5 mk1 1.8
Thanks: 0
Given 0 thank(s) in 0 post(s)
27-06-2012, 08:10 PM
(This post was last modified: 27-06-2012, 08:11 PM by MissTap_GTI6.)
(27-06-2012, 08:07 PM)strictly_derv Wrote: I would upload the pick but I havnt got the iphone cable sorry
I didn't think that one through, did I... 
Posts: 1,804
Threads: 129
Joined: Mar 2012
Reputation:
11
Thanks: 0
Given 0 thank(s) in 0 post(s)
NO. Well I got given another but forgot it!
Stage 2 XUD Sedan
Posts: 8,019
Threads: 374
Joined: Dec 2011
Reputation:
38
Location: Isle of Wight
Car Model/Spec: GTI 6
Thanks: 8
Given 16 thank(s) in 14 post(s)
DO IT!!
Im more than game to come over and chip in if you need a hand! OR, buy a new engine, and rebuild one, HDi rods, etc.....??
Posts: 4,604
Threads: 90
Joined: Dec 2011
Reputation:
54
Location: Cornwall
Car Model/Spec: 1996 306 DT M-TDI/16
Thanks: 0
Given 20 thank(s) in 18 post(s)
Gasket is meant to have little holes like thats, its to make sure water flows up around the block / head equally, otherwise it would all go up the easiest route / create hotspots etc 
| Dyno Power Runs & Steady State Facilities Available, Just Ask Anytime |
| #DervMafia |
![[Image: sigi-2.png]](http://i281.photobucket.com/albums/kk226/darrenjlobb/sigi-2.png)
Posts: 1,804
Threads: 129
Joined: Mar 2012
Reputation:
11
Thanks: 0
Given 0 thank(s) in 0 post(s)
27-06-2012, 09:21 PM
(This post was last modified: 27-06-2012, 09:22 PM by strictly_perv.)
(27-06-2012, 08:58 PM)ginge191 Wrote: DO IT!!
Im more than game to come over and chip in if you need a hand! OR, buy a new engine, and rebuild one, HDi rods, etc.....??
That would be good. Or come help with the paddle clutch fitting when it comes (will be buying it tomorrow  )
(27-06-2012, 09:08 PM)darrenjlobb Wrote: Gasket is meant to have little holes like thats, its to make sure water flows up around the block / head equally, otherwise it would all go up the easiest route / create hotspots etc
Ahh makes sense now.
Does anyone know what makes the CC difference's between the 2 engines? Bored out or shorter rods?
Stage 2 XUD Sedan
Posts: 1,737
Threads: 189
Joined: Dec 2011
Reputation:
10
Location: Salisbury/Andover
Car Model/Spec: E39 ACS 535i
Thanks: 0
Given 2 thank(s) in 2 post(s)
Should be the bore, as the 90 hdi uses the xu7 and the 110 xu9 cranks
Posts: 433
Threads: 36
Joined: Dec 2011
Reputation:
2
Thanks: 0
Given 0 thank(s) in 0 post(s)
The xud7 is 80mm bore vs 83mm xud9 iirc. Same throw
Posts: 4,604
Threads: 90
Joined: Dec 2011
Reputation:
54
Location: Cornwall
Car Model/Spec: 1996 306 DT M-TDI/16
Thanks: 0
Given 20 thank(s) in 18 post(s)
What they said^^
The XUD7 has lovely thick cylinder walls for ra*e.99 b00st tho Ive got an XUD7T block sat in my shed rusting out, might use it one day!
| Dyno Power Runs & Steady State Facilities Available, Just Ask Anytime |
| #DervMafia |
Posts: 1,804
Threads: 129
Joined: Mar 2012
Reputation:
11
Thanks: 0
Given 0 thank(s) in 0 post(s)
Should help reduce chances of a flying rod then 
Stage 2 XUD Sedan
Posts: 4,604
Threads: 90
Joined: Dec 2011
Reputation:
54
Location: Cornwall
Car Model/Spec: 1996 306 DT M-TDI/16
Thanks: 0
Given 20 thank(s) in 18 post(s)
Hm, probs wont help that, but should help once you have manned up and forged it, and throwing 100psi down the intake
| Dyno Power Runs & Steady State Facilities Available, Just Ask Anytime |
| #DervMafia |
Posts: 1,748
Threads: 41
Joined: Dec 2011
Reputation:
12
Location: Midlands
Car Model/Spec: Dtractor
Thanks: 0
Given 6 thank(s) in 6 post(s)
I would get an xud9 personally... you will just make more power with it ...
Posts: 1,220
Threads: 136
Joined: Dec 2011
Reputation:
2
Location: Norwich
Car Model/Spec: Phase 2 Dturbo
Thanks: 1
Given 1 thank(s) in 1 post(s)
If you do rebuild it with HDI rods please take lots of pictures incase I get stuck! I am about to start mine..
|
![[Image: sig.jpg]](http://i89.photobucket.com/albums/k220/c_j_m/sig.jpg)
![[Image: brokendown-1-1-1.jpg]](http://i1054.photobucket.com/albums/s491/n0v0s/brokendown-1-1-1.jpg)
![[Image: 22f2b6b2-758b-4c1c-96fb-6fa9c6059b13_zpsf306b56b.jpg]](http://i585.photobucket.com/albums/ss299/Ha11elujaz0rs/22f2b6b2-758b-4c1c-96fb-6fa9c6059b13_zpsf306b56b.jpg)