will this fit my 1.9 td for fmic
306oc - Peugeot 306 Owners Club & Forum › Engines › XUD Section v
will this fit my 1.9 td for fmic

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
will this fit my 1.9 td for fmic
finchy Offline
I'm new, be nice
Posts: 66
Threads: 19
Joined: Jan 2013
Location: coventry
Car Model/Spec: 2.0 hdi 3 door
Thanks: 0
Given 0 thank(s) in 0 post(s)
#1
15-01-2013, 08:51 PM
will this fit my 1.9 td for fmic

[Image: KGrHqRlQFCy5BELKrBQ9F2udlVw60_12_zps404e9376.jpg]

[Image: T2eC16RHJF8E9nnC7RF1BQ9F2jGZyg60_12_zpsc2a0a3ed.jpg]

[Image: T2eC16FHJFoE9nh6mQqBQ9F2dsgg60_12_zps410abfb2.jpg]

[Image: KGrHqZiIFCj9312SGBQ9F2pBLyg60_12_zpsbc820c49.jpg]
Find
Reply
Thanks given by:
Mattcheese31 Offline
Part of a Bumming Club
Moderators
Posts: 6,367
Threads: 87
Joined: Dec 2011
Reputation: 48
Location: South Yorks.
Car Model/Spec: Rouge vallelunga 5 door Dturbo
Soundcloud YouTube
Thanks: 2
Given 74 thank(s) in 70 post(s)
#2
15-01-2013, 08:52 PM
i reckon mate, what's it off? . .Smile
Phase 1 D-Turdo, K14@24 psi, De-cat, meaty backbox, Bosch pump, grinded LDA pin, duel air fed K&N =133.7bhp & 188ft/lbs
Find
Reply
Thanks given by:
finchy Offline
I'm new, be nice
Posts: 66
Threads: 19
Joined: Jan 2013
Location: coventry
Car Model/Spec: 2.0 hdi 3 door
Thanks: 0
Given 0 thank(s) in 0 post(s)
#3
15-01-2013, 08:57 PM (This post was last modified: 15-01-2013, 08:59 PM by finchy.)
http://www.ebay.co.uk/itm/111000862278?s...1423.l2648
i think its of a 406
Find
Reply
Thanks given by:
Mattcheese31 Offline
Part of a Bumming Club
Moderators
Posts: 6,367
Threads: 87
Joined: Dec 2011
Reputation: 48
Location: South Yorks.
Car Model/Spec: Rouge vallelunga 5 door Dturbo
Soundcloud YouTube
Thanks: 2
Given 74 thank(s) in 70 post(s)
#4
15-01-2013, 09:00 PM
(15-01-2013, 08:57 PM)finchy Wrote: http://www.ebay.co.uk/itm/111000862278?s...1423.l2648
i think its of a 406

yes mate should be good that . .Smile
Phase 1 D-Turdo, K14@24 psi, De-cat, meaty backbox, Bosch pump, grinded LDA pin, duel air fed K&N =133.7bhp & 188ft/lbs
Find
Reply
Thanks given by:
silverzx Offline
Always leaves skidz

Registered users - Donated
Posts: 4,926
Threads: 266
Joined: Dec 2011
Reputation: 18
Location: Somerset
Car Model/Spec: 205 DTurbo
Thanks: 73
Given 7 thank(s) in 7 post(s)
#5
16-01-2013, 12:26 PM
Make sure you grind the runners off either side if you plan to run a pipe from the turbo outlet through it.
Supercharged GTi6 Build
S14 Zenki Build
[Image: signature.png]
Find
Reply
Thanks given by:


Forum Jump:


Users browsing this thread: 1 Guest(s)