Posts: 2,489
Threads: 164
Joined: Jun 2012
Reputation:
25
Location: Honiton
Car Model/Spec: Gti6
Thanks: 0
Given 4 thank(s) in 4 post(s)
15-10-2012, 11:40 AM
(This post was last modified: 15-10-2012, 11:41 AM by rocker8742.)
Noticed a slight knocking yesterday over bumps and figured it may have been as i had people in the back which is a rare thing but had a look anyway
Found this
![[Image: 2012-10-14160210.jpg]](http://i1133.photobucket.com/albums/m598/rocker8742/2012-10-14160210.jpg)
![[Image: 2012-10-14160218.jpg]](http://i1133.photobucket.com/albums/m598/rocker8742/2012-10-14160218.jpg)
Looks like the Pass. side wheel is alot closer to the arch than the drivers and has a nice amount of camber to it but it doesnt look like the drivers does?
Am i right in thinking its a f*cked beam or is it something else?
Also looked like the passenger side is a little bit lower but not majorly different
Posts: 299
Threads: 18
Joined: Sep 2012
Reputation:
1
Location: Wiltshire
Car Model/Spec: Black ph2.5 Dturbo
Thanks: 0
Given 0 thank(s) in 0 post(s)
15-10-2012, 11:46 AM
(This post was last modified: 15-10-2012, 11:47 AM by JackLewis_Dturbo.)
you are correct! its fooked..
Posts: 47
Threads: 8
Joined: Jun 2012
Location: Cornwall
Car Model/Spec: 306 Dturbo
Thanks: 0
Given 0 thank(s) in 0 post(s)
Beam change is a piece of cake! Best get looking!!
Posts: 1,046
Threads: 71
Joined: May 2012
Reputation:
4
Location: cornwall
Car Model/Spec: 205 dt
Thanks: 0
Given 0 thank(s) in 0 post(s)
15-10-2012, 12:34 PM
(This post was last modified: 15-10-2012, 12:35 PM by kernow_joe.)
as nath said simple job hardest part is lining it up to fit it back on again
![[Image: signiture.jpg]](https://lh4.googleusercontent.com/-7ORHe1luJy0/UIW7RcRdrGI/AAAAAAAABjE/n7i9b1goCYM/s500/signiture.jpg)
Midnightclub Wrote:All the cool kids have ph 2 Nile 6's!
Posts: 2,489
Threads: 164
Joined: Jun 2012
Reputation:
25
Location: Honiton
Car Model/Spec: Gti6
Thanks: 0
Given 4 thank(s) in 4 post(s)
15-10-2012, 06:19 PM
(This post was last modified: 15-10-2012, 06:20 PM by rocker8742.)
Damn, best get on to it then
Anyone know how much a refurbed beam goes for?
Posts: 5,203
Threads: 110
Joined: Jan 2012
Reputation:
20
Location: Devon
Car Model/Spec: Estate, DT, GTI6 and 205
Thanks: 1
Given 30 thank(s) in 30 post(s)
That's a pain you need a new rear beam mate! Recon 1s are a fair bit! There's a company at stockland that do them but there about £400 I think. Best to get a 2nd hand 1 for about £100
Posts: 8,749
Threads: 208
Joined: Jan 2012
Reputation:
60
Location: Wiltshire
Car Model/Spec: ph2 Gti6 / ph4 HDI Estate
Thanks: 1
Given 5 thank(s) in 5 post(s)
Yep that beam is fooked pal, mass amounts of camber!
Recon beam = £350-450 aswell as your fooked beam
But and theres always a but. i was chatting to a guy at fcs that can supply the new bearings for £45 if your willing to have a crack at it?
I will find his card out if you want the bearings
![[Image: DSC_0190-Copy_zpsf093f84d.jpg]](http://i1038.photobucket.com/albums/a468/167gti8/DSC_0190-Copy_zpsf093f84d.jpg)
Member of 99% warning or your nothing club!
Posts: 47
Threads: 8
Joined: Jun 2012
Location: Cornwall
Car Model/Spec: 306 Dturbo
Thanks: 0
Given 0 thank(s) in 0 post(s)
Posts: 2,489
Threads: 164
Joined: Jun 2012
Reputation:
25
Location: Honiton
Car Model/Spec: Gti6
Thanks: 0
Given 4 thank(s) in 4 post(s)
16-10-2012, 10:12 AM
(This post was last modified: 16-10-2012, 10:13 AM by rocker8742.)
(15-10-2012, 07:26 PM)puglove Wrote: Yep that beam is fooked pal, mass amounts of camber!
Recon beam = £350-450 aswell as your fooked beam
But and theres always a but. i was chatting to a guy at fcs that can supply the new bearings for £45 if your willing to have a crack at it?
I will find his card out if you want the bearings
Cheers mate but wouldnt have a clue where to start lol
Think i may buy a second hand beam and might buy a few extras for it before it goes on, will be alright driving on this one for a while i woulda thought?
Also May have to get you to come give me a hand matt lol
Posts: 14,208
Threads: 448
Joined: Dec 2011
Reputation:
51
Location: isle of wight
Car Model/Spec: Pov. Spec White '6
Thanks: 17
Given 18 thank(s) in 18 post(s)
BecauseModifiedTraillingArms?
![[Image: 20A1806D-891D-40FB-BD52-AD519177A607-734...391753.jpg]](http://i35.photobucket.com/albums/d196/mattbush/20A1806D-891D-40FB-BD52-AD519177A607-7340-0000058F46391753.jpg)
TEAM CONROD SHITTING RALLYE!
Posts: 6,569
Threads: 183
Joined: Dec 2011
Reputation:
20
Location: eastwood/notts
Car Model/Spec: moonstone hdi #2
Thanks: 0
Given 8 thank(s) in 8 post(s)
I have a good beam for sale dude. £150 collected. Already lowered 60mm
#2 Moonstone Blue HDI
![[Image: 6b0c7309-5184-463c-9f73-2a7b96601418_zpsfdf041fe.jpg]](http://i512.photobucket.com/albums/t326/kent16_2008/6b0c7309-5184-463c-9f73-2a7b96601418_zpsfdf041fe.jpg)
Posts: 7,152
Threads: 130
Joined: Jan 2012
Reputation:
82
Location: Kingston
Car Model/Spec: 106 GO-NAD
Thanks: 0
Given 0 thank(s) in 0 post(s)
(16-10-2012, 10:17 AM)Matt Wrote: BecauseModifiedTraillingArms?
3 degrees of negative camber FTW
Member of the 99% warning or you're nothing club
Posts: 8,749
Threads: 208
Joined: Jan 2012
Reputation:
60
Location: Wiltshire
Car Model/Spec: ph2 Gti6 / ph4 HDI Estate
Thanks: 1
Given 5 thank(s) in 5 post(s)
(16-10-2012, 10:31 AM)kentiiboii Wrote: I have a good beam for sale dude. £150 collected. Already lowered 60mm
Bit steep ent it kent ? 
Get some solid mounts why your at it 
Member of 99% warning or your nothing club!
Posts: 5,203
Threads: 110
Joined: Jan 2012
Reputation:
20
Location: Devon
Car Model/Spec: Estate, DT, GTI6 and 205
Thanks: 1
Given 30 thank(s) in 30 post(s)
(16-10-2012, 10:12 AM)rocker8742 Wrote: (15-10-2012, 07:26 PM)puglove Wrote: Yep that beam is fooked pal, mass amounts of camber!
Recon beam = £350-450 aswell as your fooked beam
But and theres always a but. i was chatting to a guy at fcs that can supply the new bearings for £45 if your willing to have a crack at it?
I will find his card out if you want the bearings
Cheers mate but wouldnt have a clue where to start lol
Think i may buy a second hand beam and might buy a few extras for it before it goes on, will be alright driving on this one for a while i woulda thought?
Also May have to get you to come give me a hand matt lol
ok mate. you could come up my mates if you wanted as we got tools and all that up there to make it easier.
it should be ok to drive it for a bit like it is but it might be scrubbing on the inside of the arch but it depends how made it is
Posts: 7,825
Threads: 465
Joined: Dec 2011
Reputation:
114
Location: Cullompton Devon
Car Model/Spec: Vauxhall
Thanks: 1
Given 98 thank(s) in 92 post(s)
rocker there is someone local to us who recondition beams
i will try to find some info
Posts: 5,203
Threads: 110
Joined: Jan 2012
Reputation:
20
Location: Devon
Car Model/Spec: Estate, DT, GTI6 and 205
Thanks: 1
Given 30 thank(s) in 30 post(s)
(16-10-2012, 12:17 PM)cully Wrote: rocker there is someone local to us who recondition beams
i will try to find some info
http://www.sspengineering.co.uk/
we use them at work
Posts: 2,489
Threads: 164
Joined: Jun 2012
Reputation:
25
Location: Honiton
Car Model/Spec: Gti6
Thanks: 0
Given 4 thank(s) in 4 post(s)
I drive mine daily remember, dont want my teeth rattled out
Posts: 7,825
Threads: 465
Joined: Dec 2011
Reputation:
114
Location: Cullompton Devon
Car Model/Spec: Vauxhall
Thanks: 1
Given 98 thank(s) in 92 post(s)
lol yup thats the one my m8 use's
i believe he does a fitting service too
Posts: 19,854
Threads: 581
Joined: Dec 2011
Reputation:
195
Location: Bournemouth
Car Model/Spec: Supercharged 306 GTi6
Thanks: 36
Given 82 thank(s) in 78 post(s)
Nothing wrong with that. Bit of camber is epic!
Team Eaton
1999 China Blue 306 GTi6 - Eaton Supercharged - 214.5bhp 181lbft
Posts: 299
Threads: 18
Joined: Sep 2012
Reputation:
1
Location: Wiltshire
Car Model/Spec: Black ph2.5 Dturbo
Thanks: 0
Given 0 thank(s) in 0 post(s)
(16-10-2012, 02:34 PM)Niall Wrote: Nothing wrong with that. Bit of camber is epic!
true that! its shi*t that you cant adjust camber on the rear so when you get it make the most of it 
yes its f*cked but it wont come apart 
Posts: 6,569
Threads: 183
Joined: Dec 2011
Reputation:
20
Location: eastwood/notts
Car Model/Spec: moonstone hdi #2
Thanks: 0
Given 8 thank(s) in 8 post(s)
(16-10-2012, 11:17 AM)puglove Wrote: (16-10-2012, 10:31 AM)kentiiboii Wrote: I have a good beam for sale dude. £150 collected. Already lowered 60mm
Bit steep ent it kent ?
Get some solid mounts why your at it
You think? I thought that would be reasonable tbh. Been selling beams on eBay that my mate gets in for 1-120 that's standard.
#2 Moonstone Blue HDI
Posts: 8,749
Threads: 208
Joined: Jan 2012
Reputation:
60
Location: Wiltshire
Car Model/Spec: ph2 Gti6 / ph4 HDI Estate
Thanks: 1
Given 5 thank(s) in 5 post(s)
What makes yours non standard. You got solid mounts?
Member of 99% warning or your nothing club!
Posts: 6,569
Threads: 183
Joined: Dec 2011
Reputation:
20
Location: eastwood/notts
Car Model/Spec: moonstone hdi #2
Thanks: 0
Given 8 thank(s) in 8 post(s)
I ment Becuase it's lowered. It had solid mounts but selling them separate.
#2 Moonstone Blue HDI
Posts: 5,203
Threads: 110
Joined: Jan 2012
Reputation:
20
Location: Devon
Car Model/Spec: Estate, DT, GTI6 and 205
Thanks: 1
Given 30 thank(s) in 30 post(s)
|
![[Image: sig2_zps5d67efb7.jpg]](http://i1133.photobucket.com/albums/m598/rocker8742/sig2_zps5d67efb7.jpg)
![[Image: DSC_0190-Copy_zpsf093f84d.jpg]](http://s1038.photobucket.com/user/167gti8/media/DSC_0190-Copy_zpsf093f84d.jpg.html)
