Info on alloys

Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Info on alloys
#1
Getting a bit bored of my cyclones, I'm like the nimrods, how do they differ from the ouragons? Anyone shed some light on the matter ??
Reply
Thanks given by:
#2
nimrods and ouragons are the same
[Image: 00000000-0000-0000-0000-00000000014E_zpsprynorkl.jpg]
Reply
Thanks given by:
#3
Exactly the same? I've read that there is a difference in offset?
Reply
Thanks given by:
#4
same looking!
nimrods will need spacers and ouragons wont
Reply
Thanks given by:
#5
Aright, beauty, will look into it
Reply
Thanks given by:
#6
Nimrods dont 'need' spacers depending on how good your beam is. I had nimrods on with 5mm spacers on the rear, only because on one side the arch trim was a bit loose and rubbed on the tyre a little bit the other side was perfectly fine though. That said a bit of spacing makes them look better too
[Image: mcetg0.png]

ZR VVC Homebrew mapping project: http://306oc.co.uk/forum/showthread.php?tid=14360
Reply
Thanks given by:
#7
Okay, I'm guessing the difference in offset is very little then?
Reply
Thanks given by:
#8
whats those other ones, some are 15" some are 16"
[Image: Untitled-1_zpsc57da38e.jpg]
Reply
Thanks given by:
#9
Also best to remember there all stamped ouragon's even nimrods



Reply
Thanks given by:
#10
Any chance anyone knows the offset of both two alloys ?
Reply
Thanks given by:
#11
the ones off the 206 are ET31 IIRC and the ones off the 406 (the ones you want) are ET18

Also dont believe this crap about not needing spacers as narrowing your track width by over an inch will make the wheels look lostin the arches and adversely affect the handling. They might also catch suspension and brakes if you have got non standard parts.
Reply
Thanks given by:
#12
For nimrods you need 13mm spacers too bring them to the correct et
[Image: 20A1806D-891D-40FB-BD52-AD519177A607-734...391753.jpg]
TEAM CONROD SHITTING RALLYE!
Reply
Thanks given by:
#13
Ansum job
Reply
Thanks given by:
#14
Yea but you don't 'need' the spacers, I was on standard suspension and brakes for a dturbo. they would look better with some proper spacing and I was trying to find some 20mm hubcentrics shortly before selling
Handling, no doubt the shorter width affected it but I never noticed it in day to day driving
If you want to do it properly get the spacers
[Image: mcetg0.png]

ZR VVC Homebrew mapping project: http://306oc.co.uk/forum/showthread.php?tid=14360
Reply
Thanks given by:
#15
Would these be alright to run http://www.ebay.co.uk/itm/360730246825?v...1423.l2649 I'm not sure if the bolts would be suitable.
Bye Bye D-Turbo
Phase 1 GTi-6 now has a new owner
Rolling in the: Phase 3 HDI Wagon

The current estate project: http://306oc.co.uk/forum/thread-22237.html
Reply
Thanks given by:
#16
(27-12-2013, 12:25 AM)padge Wrote: whats those other ones, some are 15" some are 16"
I always thought Nimrods were 16" and Ouragon were 15"?
MG ZR TD+ - gone and easily forgotten
Fabia vRS PD130 - New daily
Astra H VXR - new toy!
Reply
Thanks given by:
#17
(27-12-2013, 11:09 PM)Dicky Wrote:
(27-12-2013, 12:25 AM)padge Wrote: whats those other ones, some are 15" some are 16"
I always thought Nimrods were 16" and Ouragon were 15"?

Nope, because there are 14" versions as well.

Ouragan's tend to be 15" and Nimrods 16". Nimrods are usually found on 206's.

the 15" come off 406's, they're the ones to have Big Grin I have a set on my 106 GTi.
A moments silence please, for our brothers in the NAD-zone.
Reply
Thanks given by:


Forum Jump:


Users browsing this thread: 1 Guest(s)