Hunter the B-road sigma.. - Printable Version

Hunter the B-road sigma.. - Printable Version

+- 306oc - Peugeot 306 Owners Club & Forum (https://www.306oc.co.uk/forum)
+-- Forum: Photos and Projects (https://www.306oc.co.uk/forum/forumdisplay.php?fid=20)
+--- Forum: 306 Projects (https://www.306oc.co.uk/forum/forumdisplay.php?fid=3)
+--- Thread: Hunter the B-road sigma.. (/showthread.php?tid=74)

Pages: 1 2 3 4 5 6 7 8 9 10 11

Hunter the B-road sigma.. - ginge191 - 05-12-2011

So thought id start this off just to post updates and more likely questions i have about XUD's in general rather than spamming up the site!

From my old 1.4 Sigma to an identicle, XTDT!

So to begin, i got myself another Sigma, this time an XTDT, and i think when i drove it, it hadn't been touched in a LONG time... There were a fair few webs on it, pedals were VERY stiff but after giving it a drive around for a bit, everything come into place quite nicely.

The bodywork etc. is immaculate apart from the drivers side front quarter panel for which i have a replacement from the old pug, get that on soon!

Interior, erm.. well wood effect dash?? whats with that?? fugly as hell, got my old interior ready to put in, thinking i'll matte black it fist.
Electrics all round which all work fine....

anyway, less chat more pics!

Old:
[Image: nWbJp-1.jpg]

New:

Fairly clean engine bay, checked the turbo and its running a KKK, wanting to change this..
[Image: PhcUS-1.jpg]

Rocker Cover Gasket needed?
[Image: VdyWG-1.jpg]

Also Air filter needs replacing - i think!?

[Image: XBFL4-1.jpg]

Plans are simple
-Coilovers
-Bosch
-FMIC
-T2 Turbo

cheers Smile

My plans for this are to create an island road car, for 'dicking' cars in the corner, some nice low end boost, maxing out at around 80mph, and no im not endorsing speeding, but large turbos and POOWAAAH is not what this project is about Smile

Just to update where i've got with this 'project' if you like to call it that

I've purchased:

- Coilovers
- Bosch pump
- T2 turbo
- rear beam mounts
- MBC
- boost gauge

So today i managed to change my front quarter panels over

Top panel (before)

[Image: noHr4.jpg]

also found this plug - any ideas, it was tucked next to my screen wash tank?? im assuming its a sensor for washer tank levels maybe???

Also managed to pipe in my boost gauge, managed to figure out which wires go where but never got round to wiring it - gauge reads a steady 13psi - not too bad, i was expecting a leak somewhere but helps a lot having that in!
pics of this once its all installed with a mount...

plans for next couple weeks to have the whole car lowered on coilovers and

Re: low end boooooost.... - Matt - 05-12-2011

keep it up ginge

Re: low end boooooost.... - Connor - 05-12-2011

Shiney things Big Grin

Re: low end boooooost.... - ginge191 - 05-12-2011

only just realised i have NO recent pictures of it, at all Sad

Re: B-road basher - Matt - 05-12-2011

looks awesome

Re: B-road basher - 4WayDiablo - 06-12-2011

Have a look in the crimbo pics for recent ones :-)

Re: B-road basher - ginge191 - 06-12-2011

So finally got the bosch pump done with KrisB, really pleased with the work he's done - details of it all found [url="http://www.theywhoshallnotbenamed/forum/showthread.php/134002-KrisB-Overview-of-workmanship?p=1797122#post1797122"]here[/url] - fitted bosch pump with lines, injectors etc. new cambelt, tensioners, idler, water pump and so on.

few pics of the day up there

no pump..
[Image: UpcUt.jpg]

Pump

Manky water pump
[Image: z9r0P.jpg]

and general idioticness from Kris..

"hey ginge, i need to shower... my hair is soo greasy..." one of the WORST jokes ever, and yes, there were more...
[Image: k57vm.jpg]

smoking through a fuel pipe Rofl

Really good day up there!

Next on the list is a new clutch, as its not liking the new power at all and is slipping quite bad - if i gradually introduce the boos its not too bad, but foot to the floor and general "RAWW!" it doesnt like it and just screams at me Sad

So hopefully another KrisB jobby!

Re: B-road basher - ginge191 - 06-12-2011

Fitted coilovers and dropped the rear in near same time

[Image: NPqao.jpg]

hmm too low...
[Image: 5KwGh.jpg]

thats right!
[Image: TClOu.jpg]

Re: B-road basher - ginge191 - 06-12-2011

Plans from here on out are to stiffen the suspension up dramtically with a re-built rear disc beam, with some solid mounts, uprated torsion and AR bars in the new year...

get a valeo clutch fitted to stop this minor clutch slip
look into turbo upgrades, small fast sppoling turbos
uprated inernals (starting to read up on what i should get)

Re: B-road basher - ginge191 - 04-01-2012

minor update

Disc rear beam ready to fit - new discs, pads, hoses and dampers to be fitted at the same time.

[Image: IcSdy.jpg]

Spoiler painted in matt black fitting once weather drys up a bit

[Image: QpwR7.jpg]

Re: B-road basher - Dum-Dum - 04-01-2012

Looking good mate

Re: B-road basher - Kezzieboy - 04-01-2012

Looks good, still can't believe you sent the nicer, deep bumper to the scrappie though!

Re: B-road basher - lewisdmz - 04-01-2012

You are brave having coilies on the iow lol. I swear every time I go back the roads get worse, literally every road is a patchwork of potholes and bumps and shit repairs, complete joke.

Not to mention everywhere is a bloody 40. Most of the Yarmouth to Newport road has been reduced to some sort of speed limit instead of NSL since I was last back which is ridiculous.

AND whilst i'm there, Beaper Shute a 50? f*cking joke.

Eep, turned into a bit of a rant there, sorry.

Re: B-road basher - ginge191 - 05-01-2012

lol lewis its not that bad, when you take the same routes reguarly you tend to know where the holes are and can avoid them. the coilies work a treat on 'cruise nights' when you get the chavs chasing you, in the corners they pay off Smile

Re: B-road basher - ginge191 - 05-01-2012

[Image: RWKua.jpg]

shiny!

Re: B-road basher - ginge191 - 14-01-2012

So went up to see Krisb to get some work done, as usual great day up... a quite frustrating day, to say the least, but the professional he was cracked on to get the job done, couple of pics from the day.

new disc beam going on

[Image: OxVK2.jpg]

new discs on

[Image: HCSyC.jpg]

Then we had the beam on but no shocks on the car....this is the result...
http://www.youtube.com/watch?v=sEBUe-i- ... HM5EmQcBdU

Re: B-road basher - ginge191 - 06-02-2012

Latest update - Waiting on parts from ebay - new sidelights and some intercooler piping (90* bend)

Have this so far...

[Image: 7AHnV.jpg]

Also some clean-ish pics of the car as it stands (also have a spoiler to fit to finish the back off nicely, but where weather is crap its pointless...)

[Image: iQbwp.jpg]

C&C welcome

Re: B-road basher - devils_fuel - 06-02-2012

looking good

Re: B-road basher - 4WayDiablo - 06-02-2012

looking good there ginge Big Grin

B-road basher - Jonny b - 06-02-2012

Looks good pal, is that the spoiler of the s16? Fecking rear window ha ha!!! Came up a treat if it is

Re: B-road basher - me-tm - 06-02-2012

That just looks evil!

Damn, I want to do more to my car as this one is giving me inspiration, but I fear it won't pass an MOT in 2013 under the new regs. Seriously thinking about another car in the next few months. Dilemma.

Re: B-road basher - Foxy-jim - 06-02-2012

Looks decent mate! I like what you are doing!

Re: B-road basher - ginge191 - 11-02-2012

So, latest update!

Phil come round to help out re-piping my turbo inlet and to say it was tight is an understatement.

the plan and the layout consists of Turbo - U-bend - 51mm-57mm adapter - 90* piping - adapter - 90* piping.

This brings it down to the front of the engine bay, just above where the standard inlet is.

We had a little run in the car with no piping and the sounds were sexxxuualalll! we were attepting to get some chatter, but it wasn't having any of it.

Phil has all the pictures and no doutb will pop them up at some point Smile

Runs really nice and the turbo spooling sounds are awesome.

Oh, and had to do something with the oil breater also.... PLEASE dont mock, but the only available item was a ripspeed breather Doh

Re: B-road basher - ginge191 - 12-02-2012

best picture i could get of it, phil has a few of the process on his phone also.

quite tight to say the least, but all fits nicely - currently running standard filter, on the prowl for a decent cone

[Image: 0uBns.jpg]

Re: B-road basher - Curt - 12-02-2012

Looks awesome dude, nice height and love the Speedlines Cool

Re: B-road basher - ginge191 - 12-02-2012

Curt Wrote:Looks awesome dude, nice height and love the Speedlines

thanks mate Smile

still seems too low at points though, likes to bottom out on large dips and potholes, might consider some stiffer springs at some point

Re: B-road basher - 4WayDiablo - 12-02-2012

As promised....
[Image: IMG_20120210_172050.jpg]

And the RIPSPEED oil breather filter
[Image: IMG_20120210_171432.jpg]

Re: B-road basher - 4WayDiablo - 12-02-2012

Also epic colour coding the silicone haha and stupid cunting photobucket compressing my images!

Re: B-road basher - ginge191 - 12-02-2012

Also note the bulkhead with auto defence! open bolts ftl Sad

Re: B-road basher - ginge191 - 14-02-2012

[Image: 395438_10151275741115632_765675631_22622...9327_n.jpg]

new filter installed, next on the list - catch tank as the cheap ass breather already is pissing everywhere..