Intake manifold hose size? - Printable Version +- 306oc - Peugeot 306 Owners Club & Forum (https://www.306oc.co.uk/forum) +-- Forum: Engines (https://www.306oc.co.uk/forum/forumdisplay.php?fid=16) +--- Forum: DW10 HDi section (https://www.306oc.co.uk/forum/forumdisplay.php?fid=10) +--- Thread: Intake manifold hose size? (/showthread.php?tid=29486) |
Intake manifold hose size? - JTaylor2005 - 01-03-2015 Hey all. Does anyone know what size that little rubber pipe is that goes between the turbo outlet pipe and the inlet elbow on the stock intake setup? If I disturb it to try and fix the boost leak I have I would probably replace it and the jubilee clamps as well to make sure it doesn't leak again haha. RE: Intake manifold hose size? - shervo - 01-03-2015 41mm iirc. Someone will be along to confirm this. ASH on ebay sell a 40mm that will squeeze on. RE: Intake manifold hose size? - Poodle - 01-03-2015 Aren't you going front mount soon? Just do it then, save the effort imo. RE: Intake manifold hose size? - JTaylor2005 - 01-03-2015 Just to be sure im on about the rubber hose on the left of this image Thanks Shervo as well RE: Intake manifold hose size? - shervo - 01-03-2015 Oh I was on about the one on the turbo side. I have my old inlet elbow at my unit ill check what size it is tomorrow for you. But as said probably better of waiting till you go front mount haha. RE: Intake manifold hose size? - JTaylor2005 - 01-03-2015 Yeah but that will probably be a while now :/ got a lot of expenses so I just want it to be a nice reliable stage 1 for a bit first want it running as sweet as possible RE: Intake manifold hose size? - shervo - 02-03-2015 (01-03-2015, 09:10 PM)JTaylor2005 Wrote: Yeah but that will probably be a while now :/ got a lot of expenses so I just want it to be a nice reliable stage 1 for a bit first want it running as sweet as possibleJust measured the small silicone coming of the original inlet elbow and its 57mm ID. That then feeds down a plastic pipe to the turbo which has a 41mm ID silicone. RE: Intake manifold hose size? - JTaylor2005 - 02-03-2015 Okie dokie nice one cheers so on a 57 ID pipe im probably looking about 63mm OD ish? How long would you say the 57mm hose bit is? Ebay has one thats 4" long but not sure if that would be long enough. Cheers for the help mate RE: Intake manifold hose size? - Poodle - 02-03-2015 Silicone will be listed in id, hard pipes in od. I think ebay also stocks rulers and calipers. RE: Intake manifold hose size? - shervo - 02-03-2015 Yeah as said silicone will be listed in ID size so just use the sizes I said. Also at a guess I would say they are each 60mm long but I can check tomorrow if you need to know. RE: Intake manifold hose size? - JTaylor2005 - 02-03-2015 This should do then http://m.ebay.co.uk/itm/111525326610?nav=SEARCH&varId=410516442956 RE: Intake manifold hose size? - shervo - 02-03-2015 Yeah 4'' of each size is plenty enough. Good luck with changing them there abit fiddly to remove especially when the jubilee clips are always positioned the wrong way haha. RE: Intake manifold hose size? - JTaylor2005 - 02-03-2015 I am only doing the top one when I put a new gasket in the elbow. I can feel the top jubilee clip already on that one so once thats off the elbow can come off and then the silicon hose as well will put it on with new clamps and fit the elbow back on RE: Intake manifold hose size? - shervo - 02-03-2015 oh lucky you then haha. If you change the jubilee clips get some genuine stainless Jubilee clips, they're way better than the generic 'hose clips'. RE: Intake manifold hose size? - JTaylor2005 - 03-03-2015 Anyone got a photo of the gaaket that goes between the elbow and the manifold? Also where the egr joins the intake now I have a blank do I need a gasket both sides of the blanking plate? RE: Intake manifold hose size? - shervo - 03-03-2015 Havent got a photo but its basically an oval shaped gasket. I just used the oval shaped gasket, the egr metal gasket blank plate and a smear of instant gasket on both sides of everything and mine has never leaked again since. RE: Intake manifold hose size? - JTaylor2005 - 03-03-2015 Haha cheers I will get my self down peugeot and see what I can get haha RE: Intake manifold hose size? - shervo - 03-03-2015 Yeah I think the gakset is only like 49p some people use 2 but IMO one is sufficient. |