+- 306oc - Peugeot 306 Owners Club & Forum (https://www.306oc.co.uk/forum)
+-- Forum: 306 Repairs & Mods (https://www.306oc.co.uk/forum/forumdisplay.php?fid=22)
+--- Forum: Electrics (https://www.306oc.co.uk/forum/forumdisplay.php?fid=23)
+--- Thread: Time/temperature unit (/showthread.php?tid=13876)
Time/temperature unit - Aaron _d95 - 15-05-2013
I have a 98 phase 2 dturbo and it has this style clock just time
![[Image: va9e4epu.jpg]](http://img.tapatalk.com/d/13/05/16/va9e4epu.jpg)
And it stopped lighting up so swapped it and now does this
![[Image: azyny6am.jpg]](http://img.tapatalk.com/d/13/05/16/azyny6am.jpg)
How do I get it like this
![[Image: y7eny2ah.jpg]](http://img.tapatalk.com/d/13/05/16/y7eny2ah.jpg)
Do I need a out side temperature receiver type thing I need to get and plug in under the engine bay.
RE: Time/temperature unit - Toms306 - 15-05-2013
You need a temp sensor yes.....they are located in the passenger wing mirror, wouldnt be accurate in the bay (not that the 306 one is accurate anyway lol).
Time/temperature unit - Aaron _d95 - 15-05-2013
(15-05-2013, 10:35 PM)Toms306 Wrote: You need a temp sensor yes.....they are located in the passenger wing mirror, wouldnt be accurate in the bay (not that the 306 one is accurate anyway lol).
You can't rely on anything on them to be accurate. My fuel gauge doesn't go past 3/4 and goes down to 1/2 in a week and then takes 3 weeks to go from 1/2 to the low warning light and that will go on and off for about 20 miles until it comes on and stays until I fill up. Ha. And my rev counter always reads 0rpm
RE: Time/temperature unit - Toms306 - 15-05-2013
Well it sounds like you bigger issues than not knowing the temperature outside then haha.
Time/temperature unit - Aaron _d95 - 15-05-2013
(15-05-2013, 10:46 PM)Toms306 Wrote: Well it sounds like you bigger issues than not knowing the temperature outside then haha.
True but its just enoying seeing the --- degrees. The fuel gauge is accurate when it's below half a tank just not above so could be the float catching in something if someone has took it out and not put it back in the same place
RE: Time/temperature unit - devils_fuel - 16-05-2013
Tom, got a sensor as i'd like one
RE: Time/temperature unit - Toms306 - 16-05-2013
No I don't Chris, binned two last week!
RE: Time/temperature unit - londondan86 - 16-05-2013
To get the temp gauge working get a sensor off I wing mirror from the scrappy and join it to the last 2 wires on the clock closest to the glove box. I routed the wires down to the front bumper where I cable tied the sensor.
Time/temperature unit - Aaron _d95 - 16-05-2013
(16-05-2013, 09:42 AM)londondan86 Wrote: To get the temp gauge working get a sensor off I wing mirror from the scrappy and join it to the last 2 wires on the clock closest to the glove box. I routed the wires down to the front bumper where I cable tied the sensor.
Ok thanks. Could I just get a mirror with a sensor and put that on
RE: Time/temperature unit - londondan86 - 16-05-2013
Depends if your door loom has the wiring for it. My dt didn't so I had to do it by the above method. Best way to check is to take your current mirror off and have a look if the wires are there taped up. It's on the passenger side by the way.
Time/temperature unit - Aaron _d95 - 16-05-2013
(16-05-2013, 05:04 PM)londondan86 Wrote: Depends if your door loom has the wiring for it. My dt didn't so I had to do it by the above method. Best way to check is to take your current mirror off and have a look if the wires are there taped up. It's on the passenger side by the way.
Thanks
RE: Time/temperature unit - Triggerpt - 18-06-2015
One question, I'm from Portugal, the driver side is the left, the temperature sensor will be where?!?
RE: Time/temperature unit - Ben_w - 18-06-2015
Have a look at the wing mirrors. You'll see a little lump on the bottom one of them. Suspect it will still be the same side. Drivers side for you guys
RE: Time/temperature unit - Triggerpt - 21-06-2015
Hi, I have checked that out, and there has nothing, my question is, does the car have the plug for the mirror sensor(if I need to check that, how do I remove the mirror?) or do I have to make some gadget to make it work?