+- 306oc - Peugeot 306 Owners Club & Forum (https://www.306oc.co.uk/forum)
+-- Forum: Photos and Projects (https://www.306oc.co.uk/forum/forumdisplay.php?fid=20)
+--- Forum: 306 Projects (https://www.306oc.co.uk/forum/forumdisplay.php?fid=3)
+--- Thread: Bianca xud GT20 (/showthread.php?tid=19632)
RE: Bianca xud GT20 - padge - 14-03-2014
ayeeee its on the to do list mate, main thing atm is making sure the motors good.
RE: Bianca xud GT20 - Chris_90 - 14-03-2014
Keep spraying stuff with wd40 till the wine stops once it's stops you no it's the last thing you sprayed with oil
RE: Bianca xud GT20 - padge - 17-03-2014
heads pressurising up again, 90-95c cold heaters..
RE: Bianca xud GT20 - sam - 17-03-2014
hope the head hasn't gone yet dude!
RE: Bianca xud GT20 - padge - 17-03-2014
don't know what to do with it now.
RE: Bianca xud GT20 - sam - 17-03-2014
keep at it boyo its a smart dt dude
RE: Bianca xud GT20 - zx_volcane - 17-03-2014
(17-03-2014, 08:30 PM)padge Wrote: heads pressurising up again, 90-95c cold heaters..
assume you put a good head on it, skimmed / pressure tested ..etc?
RE: Bianca xud GT20 - Piggy - 17-03-2014
(17-03-2014, 08:46 PM)zx_volcane Wrote:(17-03-2014, 08:30 PM)padge Wrote: heads pressurising up again, 90-95c cold heaters..
assume you put a good head on it, skimmed / pressure tested ..etc?
yeah, this....can't see why it would blow again!?
Bianca xud GT20 - Sambarker - 17-03-2014
Scrap it
RE: Bianca xud GT20 - padge - 17-03-2014
tbh, torqueing the headbolts down with a breaker bar probably didn't help..
RE: Bianca xud GT20 - Chris_90 - 17-03-2014
(17-03-2014, 09:00 PM)Piggy Wrote:(17-03-2014, 08:46 PM)zx_volcane Wrote:(17-03-2014, 08:30 PM)padge Wrote: heads pressurising up again, 90-95c cold heaters..
assume you put a good head on it, skimmed / pressure tested ..etc?
yeah, this....can't see why it would blow again!?
This wasn't done
But if you find money there's the head off my engine ready to go would even lend a hand if needed to fit it.
RE: Bianca xud GT20 - Tom - 17-03-2014
(17-03-2014, 09:30 PM)padge Wrote: tbh, torqueing the headbolts down with a breaker bar probably didn't help..
I bet that didnt effect it that much. If your worried torque them down a bit more. If you followed the stages guessing then done the angles aswell you cant be "that" far off lol :p
RE: Bianca xud GT20 - padge - 17-03-2014
nippy to dannys tomorrow, to torque them all down properly, it only started doing it after a harsh pull off from a junction lol.
RE: Bianca xud GT20 - zx_volcane - 17-03-2014
have you tried re-torqueing them?
might give you a bit more life
RE: Bianca xud GT20 - Curt - 17-03-2014
If they weren't torqued down at all that's pretty crazy. The final stage has to be done with a breaker bar but not the first 2.
RE: Bianca xud GT20 - Danny2009 - 17-03-2014
Need some arp studs
RE: Bianca xud GT20 - Tom - 17-03-2014
Yeah that'll do! I have a torque wrench here i never use, shame it would be a pain to lend it to you!
RE: Bianca xud GT20 - padge - 17-03-2014
wanted it on the rollers end of this month..
RE: Bianca xud GT20 - Danny2009 - 17-03-2014
See what it's like when I've torqued it down pal
RE: Bianca xud GT20 - padge - 18-03-2014
went out to check the water, and there was none even in it, went to top it up and the water just fell out the bottom of the rad, so looks like I just need a new rad.
RE: Bianca xud GT20 - Piggy - 18-03-2014
Phew!!!!
But doesnt explain the pressurising?!
RE: Bianca xud GT20 - padge - 18-03-2014
I didn't actually check the pressure, I just assumed it was lol.
RE: Bianca xud GT20 - padge - 18-03-2014
Nevermind still doing it opened top bleed screw near matrix and water blasts out of there
RE: Bianca xud GT20 - Mattcheese31 - 18-03-2014
Rad has probably popped because its pressurising mate...I had similar on my red one, blew bottom hose off.
RE: Bianca xud GT20 - padge - 18-03-2014
One of the small pipes had come off, put it back on put water in it and it still pressures up, going to try torquing bolts down properly tomorrow, if thats no good, then time for another hg lol..
RE: Bianca xud GT20 - padge - 21-03-2014
Head is now off this, will be dropping it off for skimming/testing monday/tuesday and should be built back up thursday
RE: Bianca xud GT20 - ash23 - 21-03-2014
good to see your keeping it and fixing it again im sure it will be worth it.
bout time you coded the side strips tho haha :p
RE: Bianca xud GT20 - padge - 21-03-2014
And rear bumper i know lol
RE: Bianca xud GT20 - Tom - 22-03-2014
Getting there Kyle, i know what your feeling all to well! It will be back soon and it will be epic!
RE: Bianca xud GT20 - Matt - 22-03-2014
Torque it up this time!