+- 306oc - Peugeot 306 Owners Club & Forum (https://www.306oc.co.uk/forum)
+-- Forum: Photos and Projects (https://www.306oc.co.uk/forum/forumdisplay.php?fid=20)
+--- Forum: 306 Projects (https://www.306oc.co.uk/forum/forumdisplay.php?fid=3)
+--- Thread: Hunter continued with a td04! (/showthread.php?tid=6168)
RE: Hunter continued.... - puglove - 10-01-2013
Looking good pal, must be somthing about 5dr sigma DT's rejecting the heater matrix at the mo
RE: Hunter continued.... - Tom - 10-01-2013
(10-01-2013, 05:55 PM)puglove Wrote: Looking good pal, must be somthing about 5dr sigma DT's rejecting the heater matrix at the mo
That was a pain in the pisser! I've only just put the last bits of trim back on because my fans broke aswell :/
RE: Hunter continued.... - puglove - 10-01-2013
(10-01-2013, 06:06 PM)Tom Wrote: That was a pain in the pisser! I've only just put the last bits of trim back on because my fans broke aswell :/
yeah i was reminded of what a PITA it was 2 weeks ago, all that fooking about then it takes 30 seconds to do the actual job lol. and yeah i fooked the fans 1st time i done it many moons ago, did you snap all the cable holders?
RE: Hunter continued.... - Tom - 10-01-2013
Cables for what met? I dont think i did
RE: Hunter continued.... - puglove - 10-01-2013
For the heater fans, or are you talking about the other fans? lol
RE: Hunter continued.... - Tom - 10-01-2013
Oooohhh on the actual heater control panel or heater box? Either way nope they were all fine
RE: Hunter continued.... - puglove - 10-01-2013
I thought you were on about the heater control lol my bad
RE: Hunter continued.... - Tom - 10-01-2013
On that subject i dont know how the f*ck your spose to get those panels out! My one is properly wedged in there and the cables are tigh as assholes :/
RE: Hunter continued.... - samass - 11-01-2013
What? Tight as arseholes? What's the issue then?
RE: Hunter continued.... - puglove - 11-01-2013
(10-01-2013, 07:40 PM)Tom Wrote: On that subject i dont know how the f*ck your spose to get those panels out! My one is properly wedged in there and the cables are tigh as assholes :/
Dont is the answer to that lol. They arr twice as hard to get the buggers back in again.
RE: Hunter continued.... - Tom - 11-01-2013
I need to replace mine because its lost 2 fan speeds
Im just demisting on 2 atm and its pretty shit lol.
RE: Hunter continued.... - puglove - 11-01-2013
More than likly to be the resister in the air duct under the scuttle panel mate.
RE: Hunter continued.... - Tom - 11-01-2013
(11-01-2013, 12:18 PM)puglove Wrote: More than likly to be the resister in the air duct under the scuttle panel mate.
Nope not that one bud, that had died aswell so i had no fans, replaced that and got 1 and 2 back but the switch is also shit so i need to change that aswell
![[Image: 20130111_121902.jpg]](http://i817.photobucket.com/albums/zz92/tomw1123/20130111_121902.jpg)
![[Image: 20130111_121913.jpg]](http://i817.photobucket.com/albums/zz92/tomw1123/20130111_121913.jpg)
Whoring the drums a bit aswell
Kudos to CJ aswell here these plates arent easy or quick to make, so anyone that says his are expensive make some yourself then see how you feel lol!
RE: Hunter continued.... - Tom - 14-01-2013
Ready to rock now we are! Had to make another plate because i cocked up some measurements but o well :p
![[Image: IMG_20130114_142826.jpg]](http://i817.photobucket.com/albums/zz92/tomw1123/IMG_20130114_142826.jpg)
![[Image: IMG_20130114_145706.jpg]](http://i817.photobucket.com/albums/zz92/tomw1123/IMG_20130114_145706.jpg)
![[Image: IMG_20130114_145658.jpg]](http://i817.photobucket.com/albums/zz92/tomw1123/IMG_20130114_145658.jpg)
![[Image: IMG_20130114_160935.jpg]](http://i817.photobucket.com/albums/zz92/tomw1123/IMG_20130114_160935.jpg)
Then put it all together!
![[Image: IMG_20130114_162055.jpg]](http://i817.photobucket.com/albums/zz92/tomw1123/IMG_20130114_162055.jpg)
Still need to have a field day with the grinder and trim a couple of bolts and get some sealant of some kind but now bar the oil line im ready to go. Think im going to change the oil and filter aswell while im there and a new intercooler d seal and manifold gasket
RE: Hunter continued.... - samass - 14-01-2013
That looks a bit pissed?
RE: Hunter continued.... - Tom - 14-01-2013
It does in the picture haha... Bit worried now, im pretty sure its the angle its sitting and the angle the picture was taken at!
RE: Hunter continued.... - Tom - 15-01-2013
Started claying the car today... I'm claying polishing and waxing individual panels then moving onto the next one.... Done the bonnet today! Pictures to follow
RE: Hunter continued.... - ozonehostile - 15-01-2013
I need to clay and give mine an extreme t cut and polish. so many scratches from its time in the garage.
your turbo looks well good, nicely done
RE: Hunter continued.... - Tom - 15-01-2013
A picture. Multi story, bit of beading, it'll do.
![[Image: IMG_20130115_222549.jpg]](http://i817.photobucket.com/albums/zz92/tomw1123/IMG_20130115_222549.jpg)
Then instagramed that shit.
![[Image: IMG_20130115_222616.jpg]](http://i817.photobucket.com/albums/zz92/tomw1123/IMG_20130115_222616.jpg)
That is all.
RE: Hunter continued.... - Tom - 16-01-2013
Got the roof clayed and polished and waxed today! Going to try for a whole side of the car tomorrow
RE: Hunter continued.... - strictly_perv - 16-01-2013
The turbo build looked really nice until the sheet you've used for the mani plate, at least cut the edges? The sheer weight of that will probably add so much weight it'll be slower than the K03
RE: Hunter continued.... - Tom - 16-01-2013
(16-01-2013, 06:43 PM)strictly_derv Wrote: The turbo build looked really nice until the sheet you've used for the mani plate, at least cut the edges? The sheer weight of that will probably add so much weight it'll be slower than the K03
Its f*cking heavy haha. It will be tidied up at some point, would of been done yesturday but the grinder met its untimely demise
RE: Hunter continued.... - Tom - 19-01-2013
Clayed and de greased looking good, ready for some polishing later on
![[Image: IMG_20130119_133508.jpg]](http://i817.photobucket.com/albums/zz92/tomw1123/IMG_20130119_133508.jpg)
![[Image: IMG_20130119_135125.jpg]](http://i817.photobucket.com/albums/zz92/tomw1123/IMG_20130119_135125.jpg)
RE: Hunter continued.... - ozonehostile - 19-01-2013
this entire thread just seems to be turbo-polishing-turbo-polishing-turbo-polishing hahah
but still, looking real nice
RE: Hunter continued.... - Tom - 23-01-2013
(19-01-2013, 04:10 PM)ozonehostile Wrote: this entire thread just seems to be turbo-polishing-turbo-polishing-turbo-polishing hahah
but still, looking real nice
Is that not the best way?
Off to the garage now to get some top quality Michelin rubber fitted!
RE: Hunter continued.... - ginge191 - 23-01-2013
you're missing a dust cap...
RE: Hunter continued.... - Tom - 23-01-2013
Not anymore got new ones now
RE: Hunter continued.... - ginge191 - 23-01-2013
(23-01-2013, 02:31 PM)Tom Wrote: Not anymore got new ones now
Let me guess... Blue chrome? Dice? LED's?
RE: Hunter continued.... - ozonehostile - 23-01-2013
Let us know what michelin performance Is like, I badly need some new rubber but putting it off until I get my 16" rims.
Thinking of tying some Kumho or falcon as toyo are useless on anything other than smooth Welsh roads on a hot day
RE: Hunter continued.... - Tom - 23-01-2013
(23-01-2013, 02:37 PM)ginge191 Wrote:(23-01-2013, 02:31 PM)Tom Wrote: Not anymore got new ones now
Let me guess... Blue chrome? Dice? LED's?
To match my neons init m8.
(23-01-2013, 05:51 PM)ozonehostile Wrote: Let us know what michelin performance Is like, I badly need some new rubber but putting it off until I get my 16" rims.
Thinking of tying some Kumho or falcon as toyo are useless on anything other than smooth Welsh roads on a hot day
So far so good, Done about 50miles on them today and theyre quieter, feel smoother, and the turn in feels a bit sharper, Oh and you just throw it round and it just sticks big fat thumbs up here