+- 306oc - Peugeot 306 Owners Club & Forum (https://www.306oc.co.uk/forum)
+-- Forum: Engines (https://www.306oc.co.uk/forum/forumdisplay.php?fid=16)
+--- Forum: XUD Section (https://www.306oc.co.uk/forum/forumdisplay.php?fid=11)
+--- Thread: TD04 Clearnace (/showthread.php?tid=878)
Pages:
1
2
Re: TD04 Clearnace - Dan! - 26-01-2012
Aye, K03 and GT15 share the same mani
Re: TD04 Clearnace - Harky - 26-01-2012
Checked mine the other day and it ain't hitting the bulkhead so yeap, possible with no bashing!
Think one of my rattles was one of the pipes going to the mbc, was sitting up against the brake servo in a funny kinda way. Other noise's just coming from the exhaust leaking, going to pull it off tonight and try and seal it up again...then ready to start trying to get some decent boost!
Re: TD04 Clearnace - studturbo - 28-01-2012
Witch one of theses mani would be better for my TD04 as i got it today t2 mani or a kkk mani ?
Re: TD04 Clearnace - mark_airey - 28-01-2012
studturbo Wrote:Witch one of theses mani would be better for my TD04 as i got it today t2 mani or a kkk mani ?
The T2 and K14 use the same manifold..............the gt15 uses the other design which allows the turbo to sit slightly lower
Re: TD04 Clearnace - studturbo - 28-01-2012
I aint got a gt15 manifold
what thay like on the t2 manifold ?
Re: TD04 Clearnace - ash23 - 28-01-2012
no waste gate on a t2/k14 mani
Re: TD04 Clearnace - studturbo - 28-01-2012
I could if i mount waste gate under neaf it tho couldnt i ?
look at this http://www.theywhoshallnotbenamed/forum/showthread. ... light=td04
Re: TD04 Clearnace - mark_airey - 28-01-2012
studturbo Wrote:I could if i mount waste gate under neaf it tho couldnt i ?
look at this http://www.theywhoshallnotbenamed/forum/showthread. ... light=td04
Nope, there isn't room for the actuator in any position which will allow you to reach the wastegate arm! Just weld it closed and stop messing about :p
Re: TD04 Clearnace - studturbo - 28-01-2012
Weld it shut lol
Re: TD04 Clearnace - ash23 - 28-01-2012
or use the k03/gt15 manifold and have proper control over your boost
Re: TD04 Clearnace - studturbo - 28-01-2012
where would i get a k03/gt15 one from cos am not buying full turbo lol
Re: TD04 Clearnace - ash23 - 28-01-2012
i would assume the scrappers / ebay will have one
Re: TD04 Clearnace - studturbo - 28-01-2012
Ill try ebay and my m8s just scraped a 306 with a gt15 on aswell gutted
Re: TD04 Clearnace - ash23 - 28-01-2012
there is one on egay but he ants £35 for it lol scrappy near me only charged me £7 lol
Re: TD04 Clearnace - mark_airey - 28-01-2012
studturbo Wrote:Weld it shut lol
Yes, weld it shut..................
Re: TD04 Clearnace - studturbo - 28-01-2012
Where you from ash ? think ill have too have a drive down lol