+- 306oc - Peugeot 306 Owners Club & Forum (https://www.306oc.co.uk/forum)
+-- Forum: Photos and Projects (https://www.306oc.co.uk/forum/forumdisplay.php?fid=20)
+--- Forum: 306 Projects (https://www.306oc.co.uk/forum/forumdisplay.php?fid=3)
+--- Thread: Mitch's Blaze D-Turbo (/showthread.php?tid=13975)
Blaze PH2 XUD project! - Stephen - 27-06-2013
I can borrow a decent one
RE: Blaze PH2 XUD project! - Tom - 27-06-2013
I like it! Much difference with the fmic?
RE: Blaze PH2 XUD project! - Mitch - 27-06-2013
(27-06-2013, 10:14 PM)Stephen Wrote: I can borrow a decent one
I shall have nothing to do with it if it gets broken in anyway or form
(27-06-2013, 10:15 PM)Tom Wrote: I like it! Much difference with the fmic?
Thanks mate
it definitely has more torque, well it feels that way, dyno suggests that too, went from 170 ft lbs when on tmic to 204 ft lbs on the fmic, although i think that is because when i put the fmic on the smoke cleared up a lot due to the air being colder so the fuel was getting burnt easier? so obviously i could add a bit more fuel in until i was back to a slight haze on boost again, seems to just have more 'grunt' all round with the fmic, can also hear it 'chatter' on gear changes now, not good but hey ho
RE: Blaze PH2 XUD project! - Mitch - 05-07-2013
Gave it a good clean and put the black plastic rub strips on as personally i think they suit the car more?
not far of ready for fcs now, need to sort out mirror caps and get a fan of some sort rigged up!
RE: Blaze PH2 XUD project! - Mitch - 16-07-2013
The tmic is now back on, the fmic was causing the pedals to vibrate alot, due to me using the standard tmic pipe, also not really seeing the need for it, made the car slighty more laggy, goes just a well on tmic in my opinion, fmic kit is for sale, 80 pounds, including 406 inlet manifold, can bring to fcs
Got some black mirror caps to replace the paint peeling blaze ones, seem to suit the car better as the bump strips are black and the bottom half of the side skirts
Also wired up a 12" fan when i took the fmic off, as the standard ones had a mind of there own, i used a 4 pin relay, the one out of the standard fans, i presume this is okay? connected it to a switch which i have placed in the small ashtray thing behind the the handbrake, also tried to hide all the wires in the existing looms as best as i could
temporary position for the relay, all wires are now taped up
rough paint diagram of how i wired it up, there is a 15 amp fuse in the wire from the battery to the relay, can anyone tell me if this is correct?
Going to have a straight through 2 1/4 inch pipe to a 3 inch tip made tomorrow, at aa silencers in stafford, 86 pound plus the vat, they do a really good job, cannot wait!
RE: Mitch's Blaze D-Turbo - Msparksdturbo - 16-07-2013
When are we guna start tuning mine then m8 need some power now haha
RE: Mitch's Blaze D-Turbo - D Turbo Lyle - 18-07-2013
yeah dude nice car..... nice colour! ; ) what did u spray ur badges with? i was considering spraying my front and back pug badges black.. u look quite handy with cars... im jelous! haha
oh and forgot whats a "fmic" front mount intercooler? f*cking nooby question like! haha whats shes sitting at now? bhp wise?
RE: Mitch's Blaze D-Turbo - Tom - 18-07-2013
Really want fmic!
RE: Mitch's Blaze D-Turbo - Chris_90 - 18-07-2013
(18-07-2013, 05:43 PM)Tom Wrote: Really want fmic!
I believe he has took it off so may be for sale
RE: Mitch's Blaze D-Turbo - Tom - 18-07-2013
He has, says is up there dude ^^^
pay attention man!
RE: Mitch's Blaze D-Turbo - Mitch - 21-07-2013
(18-07-2013, 04:54 PM)D Turbo Lyle Wrote: yeah dude nice car..... nice colour! ; ) what did u spray ur badges with? i was considering spraying my front and back pug badges black.. u look quite handy with cars... im jelous! haha
oh and forgot whats a "fmic" front mount intercooler? f*cking nooby question like! haha whats shes sitting at now? bhp wise?
Just some random black paint from halfords, and yes fmic= front mounted intercooler, i wouldnt know to be honest, last time on the RR it was 125bhp at 19psi, only fiddled with the pump a bit since then, so around that mark, and the fmic kit is for sale, im able to bring it to fcs
RE: Mitch's Blaze D-Turbo - Mitch - 22-07-2013
had the exhaust made, quite happy with it, can still drive it pretty quietly too
Also swapped the center dash pieces and the gear knob over from the other blaze which im breaking, gear knob is from a citroen zx
RE: Mitch's Blaze D-Turbo - Piggy - 23-07-2013
nice tailpipe.
shame about not keeping the fmic...would suit the td04 more
RE: Mitch's Blaze D-Turbo - Mitch - 23-07-2013
(23-07-2013, 06:18 AM)Piggy Wrote: nice tailpipe.
shame about not keeping the fmic...would suit the td04 more
cheers! tdo4?? i have a t2
Re: Mitch's Blaze D-Turbo - CJ_Derv - 25-07-2013
TD04 on TMIC ftw get a TD04 bolted on this!!
RE: Mitch's Blaze D-Turbo - Mitch - 25-07-2013
I have sold tdo4 setup, mattcheese is having it off me at fcs!
RE: Mitch's Blaze D-Turbo - Piggy - 25-07-2013
ah thats where I got confuser
RE: Mitch's Blaze D-Turbo - Mitch - 25-07-2013
(25-07-2013, 07:28 PM)Piggy Wrote: ah thats where I got confuser
It was going to go on, need it to be reliable though as I do a fair few miles
RE: Mitch's Blaze D-Turbo - Piggy - 25-07-2013
td04 probably more reliable than hugely boosted t2!!!
is your exhaust completely straight through??
RE: Mitch's Blaze D-Turbo - Mitch - 25-07-2013
Only at 19-20 psi, still made 124bhp, which does me fine
and yes it's completely straight through
RE: Mitch's Blaze D-Turbo - Piggy - 25-07-2013
what diameter?? and where was the tip from? looks sweet and sleeper all at same time!
RE: Mitch's Blaze D-Turbo - Mitch - 25-07-2013
Cheers! 2.25 and the tip is 3 inch, all got made at AA silencers in stafford
RE: Mitch's Blaze D-Turbo - Piggy - 25-07-2013
stafford eh! thats where I growed up!!!
RE: Mitch's Blaze D-Turbo - Grant - 25-07-2013
Looking very tidy!
Nice work
RE: Mitch's Blaze D-Turbo - Mitch - 25-07-2013
(25-07-2013, 08:24 PM)Piggy Wrote: stafford eh! thats where I growed up!!!
Looks like you'll be coming back for an exhaust!
(25-07-2013, 08:27 PM)Grant Wrote: Looking very tidy!
Nice work
Cheers dude
RE: Mitch's Blaze D-Turbo - Mitch - 23-08-2013
been quite busy lately so not done a lot really, brought some black 205 gti wheels with 4 new budgets for 70 quid, clones need tyres and balancing and i cant afford any more dunlops at the moment so these will do!
RE: Mitch's Blaze D-Turbo - Matt - 23-08-2013
Looking sweet man
got any vids of the sound? I have a 2.25 exhaust to go on, but so much to sort before lol
RE: Mitch's Blaze D-Turbo - Mitch - 23-08-2013
Nope, I shall try and get one tomorrow if I get around to it
it's loudish but nothing over the top
RE: Mitch's Blaze D-Turbo - Mitch - 07-09-2013
Sort of went off the 205 wheels so the rallye's clones are now on..
Was advised at FCS to get rid of the standard inlet pipe that goes around by the master cylinder by Ruan due to how restrictive/small diameter it is, cant believe its made such a difference, got hold of some 2.25 industrial hoover pipe and a custom made pipe from ash23 to replace the bit that goes round by the master cylinder
Recommend this to all xud owners
Also got JP's lda pin in now, but currently no pictures
RE: Mitch's Blaze D-Turbo - rd070707 - 09-09-2013
Speedlines for sale?